On this page
Quick answer
A sink usually slows because hair, soap, food, grease, or debris blocks the stopper, trap, or drain line. Start by removing visible buildup, then use the right plunger, flush with hot water and dish soap, and clean the P-trap. For kitchen sinks, check the disposal. Stop if the clog is beyond the trap or a supply line leaks.
At a glance
- Time
- 15–45 min
- Difficulty
- Moderate
- You'll need
- Plunger, bucket, gloves, adjustable pliers, sink auger
- Cost
- Free for most fixes; a part if one is worn
- Works on
- Bathroom and kitchen sinks, including disposal-equipped kitchen sinks
- Not covered
- Sewer repair, gas work, wiring work, or concealed pipe replacement
Why does a sink drain slowly?
A sink drain is usually a short route made of several connected parts. Water passes through the sink opening, the tailpiece beneath the stopper, a curved trap, and the branch drain that leads to the home’s larger drain line. Each fitting can collect debris, and a blockage can form at the opening or farther down the pipe.
If you are looking for how to unclog a bathroom sink, remember that bathroom sinks commonly collect hair, soap residue, toothpaste, and skin products. When you want to know how to unclog a kitchen sink, kitchen sinks can collect food particles, coffee grounds, cooking oil, and grease. Grease can cool inside the drain and stick to the pipe instead of moving with water. A kitchen garbage disposal may also jam, but a working disposal does not protect the branch drain from food or grease entering below it.
A drain that drains slowly after a long period of inactivity may have a light buildup near the stopper. A sink that stays full, gurgles, or sends water back while another fixture drains is more likely to have a blockage farther downstream. Standing water does not by itself confirm the exact cause, so you should work from the easiest checks outward instead of dismantling the plumbing at once. This guide walks you through how to unclog a sink step by step, and each section explains how to unclog sink clogs that form near the stopper or farther down the line.
Before you start
Before any under-sink work, close the hot and cold water shutoff valves. If you cannot reach the local valves, close the home’s main water valve. Before placing your hands or tools near a garbage disposal, unplug the disposal; if it is hardwired, switch off the circuit breaker. Never open internal electrical wiring.
- Identify the setup. Check whether the bathroom sink has a pop-up stopper and whether the kitchen sink has a strainer, a disposal, or both.
- Protect the area. Place towels under the sink, set a bucket below the drain parts, and wear waterproof gloves. Keep tools from falling into the open pipe.
- Prepare basic supplies. You may need a sink plunger, flashlight, dish soap, adjustable pliers, a drain auger, toothbrush, and clean washers or gaskets for the sink you own.
- Keep chemicals separate. Do not mix drain openers, bleach, ammonia, vinegar, or other cleaners. Follow any product label exactly.
- Those tasks require a licensed professional.
If you smell gas, leave the area without operating switches or creating flames, then contact the gas utility or emergency service. If water leaks from a supply line you cannot shut off, leave the area and call the water utility or a plumber.
Step 1 Remove visible buildup from the sink opening
Why this works: Hair and debris often cling to the stopper or strainer. Removing them restores a clear opening without disturbing the plumbing below the sink.
Bathroom sink
A pop-up stopper may lift out, pull up, or release with a gentle twist. If it is stuck, do not pry it against the porcelain. Use the method supplied by the sink or faucet manufacturer when one is available.
Kitchen sink
A removable strainer may lift or twist out of the opening. If a disposal is installed, do not reach past its guard. Unplug the disposal first and use tongs rather than your fingers.
- Place a towel around the sink opening and remove the stopper or strainer.
- Use a flashlight to inspect the drain opening and the underside of the removed part.
- Pull out hair, soap clumps, food scraps, and other visible debris. Use a toothbrush or soft brush for material stuck to the strainer.
- Do not push debris farther into the pipe. If you cannot reach it from above, use a sink auger in Step 7.
- Rinse the strainer and stopper, reinstall them, and run the tap briefly to check drainage.
How to tell it worked: The water should form a normal whirlpool or circle and leave the basin without pooling. If it still drains slowly, move to plunging.
Step 2 Plunge the sink drain
Why this works: A plunger creates pressure changes that can move a soft blockage and release it from the drain opening. A sink plunger must form a tight seal over the drain.
- Remove the stopper or strainer if the plunger cup cannot seal over the opening.
- If the basin is empty, add hot tap water until the plunger cup is covered. If the basin is nearly full, remove some water first so it does not overflow.
- Place the plunger directly over the drain and press down to expel trapped air. Check the seal around the cup.
- Pump steadily while keeping the seal in place. Increase the force only as needed and keep the plunger upright.
- After several pumps, check whether the water level is falling. If the drain gurgles or another fixture moves, stop because the blockage may be farther down.
- Raise the plunger to release pressure, then repeat if the sink begins to drain slowly again. Clean the cup before storing it.
How to tell it worked: Water should drain away promptly after the seal breaks, and the basin should stay empty while the tap runs. Slow drainage after a brief improvement means you should use a more direct method.
Step 3 Flush the drain with hot water and dish soap
Why this works: Dish soap helps loosen greasy residue, while a steady flow of hot tap water carries loosened material toward the trap. This works best for light buildup rather than a hard blockage.
- Remove the stopper or strainer and clear any material you can reach from above.
- Squirt a small amount of ordinary dish soap into the drain opening.
- Let the soap sit for a few minutes while you prepare the hot water.
- Run very hot tap water steadily into the drain for several minutes. Do not use boiling water unless the fixture manufacturer specifically permits it.
- Watch the basin while the water runs and stop if it approaches the overflow opening.
- If the clog returns, do not keep adding soap or grease. Move on to a plunger, trap cleaning, or an auger.
How to tell it worked: The sink should empty evenly and should not leave a layer of water in the bottom. Any foul odor should also lessen once trapped residue is removed.
Step 4 Free a jammed kitchen garbage disposal
Why this works: If the disposal hums, stops, or leaves food trapped at its guard, the sink may appear clogged even though the drain pipe is clear. A reset or a small foreign-object jam can often be cleared without removing the unit.
- Switch off and unplug the disposal before touching the drain opening or placing a tool near the blades. If the plug is inaccessible, switch off its breaker.
- Remove the sink strainer if possible and look for an obstruction above the disposal guard. Use tongs to remove only what you can clearly see.
- If the disposal makes a humming sound but does not turn, insert the disposal wrench supplied with the unit into the port underneath. Rock the wrench back and forth while keeping your hands away from the blades.
- If the unit has a reset button, press it. Set the disposal switch to off, wait until the blades stop, and then set it to on while the drain is clear.
- Restore power and run cold tap water while the disposal turns. Stop immediately if it hums, bumps, leaks, or trips the breaker.
- If the disposal still does not turn, leave it switched off. Do not open the motor or its wiring; call a qualified technician.
How to tell it worked: The disposal should spin freely without humming or vibration, and sink water should drain normally. A humming or repeatedly tripping unit needs professional service rather than another reset.
Step 5 Clean the P-trap under the sink
Why this works: Hair, soap, grease, and food often settle in the lowest curved part of the drain. Removing this trap lets you clear the blockage and see whether water can pass beyond it.
Bathroom sink
The P-trap is usually the U-shaped section directly below the sink. Disassemble only the slip-joint fittings and keep the curved section in the same orientation when you reinstall it.
Kitchen sink without a disposal
The trap may have a different shape, but the method is similar. Clean the removable section and avoid pulling hard on the pipe connected to the wall.
- Close the hot and cold shutoff valves, place a bucket under the trap, and move items away from the cabinet.
- Loosen the slip nuts by hand. If they will not turn, use adjustable pliers with a cloth protecting the plastic, and do not crush or split the fitting.
- Remove only the trap section. Do separate the joints slowly so water and debris go into the bucket rather than onto the cabinet floor.
- Remove hair, grease, soap, and debris from the trap. Rinse the piece and the open pipe with tap water without forcing the hose into the pipe.
- For a kitchen sink with a disposal, do not twist or pull the disposal to remove the trap. Clean any accessible opening, then use an approved cleanout or call a plumber.
- Reassemble the trap with the original washers and gaskets. Tighten the slip nuts evenly until secure, but stop if a fitting cracks.
- Open the shutoff valves and run water slowly while watching every joint and the cabinet floor. Close the valves again if water leaks.
How to tell it worked: The sink should drain quickly, and no water should collect under the sink during the test. If the trap was clean but the water still backs up, the blockage is probably in the tailpiece or branch drain.
Step 6 Remove and clean the sink tailpiece
Why this works: If the stopper and trap are clear, debris may be packed into the short pipe directly under the sink. Removing the tailpiece lets you clean that section without cutting pipe or dismantling the whole drain.
- Close the water shutoff valves, place a bucket beneath the drain, and remove the sink stopper as described in Step 1.
- From below, disconnect the tailpiece at its slip nut or remove the retaining hardware that holds the drain assembly in the sink.
- For a bathroom overflow assembly, separate the linkage gently and note how each piece fits. Do not twist hard against the sink or force the linkage.
- Clean hair, soap, food, and grease from the tailpiece, drain flange, and opening. Brush the inside rather than trying to force a blockage farther down.
- Inspect the washers and gaskets for tears or flattening. Replace a damaged piece with one designed for the sink.
- Reinstall the pieces in their original order. Do not use tape in place of a gasket or an O-ring.
- Run water slowly and check both the drain connection and the overflow opening for leaks.
How to tell it worked: Water should leave the sink without pooling, and the stopper should move correctly without water escaping underneath. If the tailpiece is clear but drainage remains slow, continue to the branch drain.
Step 7 Work a sink auger into the branch drain
Why this works: A sink auger is a narrow cable with a cutting head that can reach farther than a plunger. It can break up or retrieve a blockage that lies beyond the trap without using harsh chemicals.
- For a bathroom sink, remove the P-trap as described in Step 5 so you have straight access to the branch drain. Keep the washers and fittings together for reassembly.
- Feed the auger cable into the open drain opening slowly while turning the handle. Keep your hands away from the cable and never force it past an unexplained obstruction.
- When you feel resistance, stop turning briefly, then crank and withdraw the cable several inches. Continue turning as you pull so the cutting head can break up the material.
- Repeat the feed, turn, and withdrawal process until the cable moves freely or you reach the end of the accessible pipe.
- Do not send the cable through a garbage disposal. Use only an approved cleanout, or have a plumber remove the disposal if deeper access is required.
- Do not force a toilet auger into a sink drain. Use a cable and head sized for the sink drain opening.
- When the cable moves freely, withdraw it, flush the drain with hot tap water, clean the tools, and reinstall the trap.
How to tell it worked: The sink should drain promptly and should not gurgle when another nearby fixture drains. If the cable meets firm resistance, will not pass, or retrieves no debris, stop and call a plumber.
Step 8 Use a chemical drain opener only as a last resort
Why this works: A drain opener formulated for sinks may dissolve some residue that mechanical tools cannot reach. Because the active ingredients and required procedures vary, the product label is the controlling instruction.
- Read the entire label and confirm that the product is intended for your type of sink and plumbing. Follow the label for the amount, waiting time, and water-rinsing instructions.
- Ventilate the area, wear the protective gloves and eye protection specified by the label, and keep children and pets away.
- Remove standing water if the label tells you to do so. Pour only the labeled amount into the drain.
- Wait for the full label time. Do not add another cleaner, bleach, ammonia, vinegar, or boiling water unless the label specifically directs it.
- Run water as the label directs. Stop if the drain overflows, fumes become strong, or you notice a leak.
- If the clog remains, do not repeat the chemical treatment automatically. Arrange mechanical cleaning or call a plumber.
- Store or dispose of the container according to the label and local instructions. Never pour the remaining product into a storm drain.
How to tell it worked: The sink should drain normally after the labeled treatment and a steady rinse. A slow drain, recurring backups, or unexplained odor means you should stop and use a plumber.
Symptom checker
| What you notice | Likely cause | Fix (step number) |
|---|---|---|
| Hair or food is visible around the stopper | Debris caught at the sink opening | Step 1 |
| Plunging briefly improves the flow | A soft blockage near the drain opening | Step 2 |
| The kitchen disposal hums or stops | Jammed disposal or trapped object | Step 4 |
| Debris is inside the removed P-trap | Buildup in the lowest curved pipe section | Step 5 |
| Water returns after the trap is cleaned | Clog in the tailpiece or branch drain | Steps 6–7 |
| The bathroom sink drains but the tub gurgles | Shared branch-drain blockage | Step 7; call a plumber if it remains |
| The dishwasher causes the kitchen sink to back up | Debris farther along the kitchen branch drain | Step 7; call a plumber if it remains |
| Several sinks or fixtures drain slowly | Problem in a shared drain line | Steps 5–7, then call a plumber |
| Water appears under the sink after cleaning the trap | Loose slip nut or damaged gasket | Step 5 |
Mistakes that make it worse
- Mixing drain products. Combining chemical openers can release dangerous fumes or heat and may damage the drain.
- Pouring boiling water into the sink. Hot tap water is safer for porcelain, metal, and plastic components that may be damaged by sudden extreme heat.
- Using the disposal while it is still connected to power. Shut it off and unplug it before reaching into the drain or using a tool near the blades.
- Forcing a plunger or auger. Excess force can damage the drain opening, trap, or pipe and may push the blockage deeper.
- Overtightening plastic slip nuts. Cracked fittings and stripped threads create leaks under the sink. Tighten evenly and stop when secure.
- Ignoring backups in other fixtures. If more than one drain is affected, repeated plunging or chemical treatment may only delay a needed plumbing repair.
When to call a professional
- Call a plumber if several fixtures drain slowly, gurgle, or back up at the same time.
- Get help if sewage or dirty water appears in a sink, tub, shower, or floor drain.
- Call a plumber if the blockage lies beyond the branch drain, the auger meets firm resistance, or there is no usable cleanout.
- Call a plumber if a joint keeps leaking, a pipe is cracked or corroded, or the trap cannot be removed without damage.
- If a disposal repeatedly hums, trips its breaker, or involves internal wiring, leave the power off and call a qualified appliance technician or licensed electrician. Do not open the wiring yourself.
How to keep it from happening again
- Clean the stopper or strainer regularly so hair, food, and soap do not build up at the opening.
- Use a drain catcher if hair or food debris frequently collects in the sink.
- Pour cooking oil into a container instead of the sink, and wipe greasy pans with a paper towel before washing them.
- Run only materials approved for the disposal in a kitchen sink, and avoid hard objects that can jam the blades.
- Run hot tap water after food preparation so small particles move through the drain instead of settling.
- Check under the sink for dampness, loose joints, or a slow leak before the damage becomes visible.
Frequently asked questions
Why is my sink draining slowly?
Hair, soap, food, grease, or debris is blocking some part of the drain. Start at the stopper with a plunger, then clean the trap if the sink still drains slowly.
Is it safe to pour boiling water down a sink?
Hot tap water is the safer choice because boiling water can damage some sinks, faucets, and plastic parts. Use boiling water only if the fixture manufacturer specifically allows it.
Why does the water come back after I plunge the sink?
Water returning quickly can mean the blockage is beyond the trap or in a shared drain line. Stop repeating the plunge and clean the trap or use a sink auger.
How do I know if the garbage disposal is jammed?
Humming, bouncing, or stopping when the switch is on usually points to a disposal jam. Switch off and unplug it before checking for an obstruction or using the disposal wrench.
Should I use chemical drain cleaner?
It can help with some residue, but a product should only be used according to its label and after simpler mechanical methods fail. Never mix drain chemicals, and do not add boiling water unless the label directs it.
When should I call a plumber for a clogged sink?
Call a plumber when several drains are affected, sewage appears, the auger cannot reach the blockage, or a pipe or joint leaks.
Revision history
- Updated and re-checked against sources.
- First published.
Did this fix it?
Thanks. Glad it's sorted.
Sorry it's still not right. Recheck the symptom checker above, or tell us what you're seeing.