On this page

Quick answer

A slow bathtub drain is usually caused by hair, soap buildup, or a blocked stopper. Remove the stopper and visible debris, then try a flange plunger, clear the overflow, and use a drain snake. Avoid pouring harsh drain cleaner. If water still backs up, call a plumber.

At a glance

Time
15–45 min
Difficulty
Moderate
You'll need
Bucket, towels, gloves, screwdriver, pliers, flange plunger, and drain snake
Cost
Free for most fixes; a replacement part if one is worn
Works on
Standard tubs with an accessible drain and overflow
Not covered
Main sewer clogs, hidden leaks, damaged pipes, and inaccessible underground traps

Why is my bathtub drain slow?

A bathtub drain does not send water straight to the sewer. Water passes through the drain opening, into a trap below or behind the tub, and then into the home’s drain branch. The overflow opening near the top of the tub is a backup route that helps prevent the tub from spilling over. It may collect hair and soap scum, but it is not the main path used during a normal drain.

Slow draining usually means the opening is partly blocked or the trap holds a buildup. Hair, soap residue, body oils, and small objects can form a mat near the stopper. A deeper trap can collect the same material over time. A stopper that does not open fully or a drain cover sitting low can also reduce the available opening.

If plunging and snaking produce only a short improvement, the cause may be farther down the branch, in a damaged trap, or in the main drain. If several fixtures drain slowly at once, the problem is probably not inside the tub. If only this tub is slow, start with the stopper, overflow, and trap.

Before you start

Start with the easiest accessible parts and keep water off the floor. Put towels around the tub, place a bucket under the drain, and wear gloves and eye protection. A screwdriver, needle-nose pliers, a soft brush, a flange plunger, and a tub drain snake cover most bathtub clogs. Keep a flashlight handy if the trap is under the tub.

Identify whether the tub uses a lift-out stopper, screw-in stopper, pop-up stopper, trip-lever assembly, or fixed strainer. The removal method differs, but the basic order stays the same: uncover the drain, clear the overflow, plunge, flush, and snake only if the gentler steps fail.

  • Remove bath toys, body oils, and loose hair from the drain area.
  • Do not use boiling water; it can soften some pipes and stress older plumbing.
  • Do not mix drain products, and do not use a chemical opener before plunging or snaking.
  • Keep electrical tools and powered drain accessories unplugged and away from standing water.

This procedure normally does not require shutting off the tub’s water supply. If any work will disconnect a supply fitting, close the home’s main water valve before starting, and do not remove the valve. Never work on gas lines, gas valves, gas burners, or internal electrical wiring; call a licensed professional for those tasks.

Step 1 Remove the drain cover and visible debris

Hair and soap often catch directly under the stopper or strainer. Removing this layer can restore much of the drain opening without pushing the clog farther down. It is also the safest place to check for objects that should not enter the plumbing.

  1. Place a bucket under the drain and drape towels over the tub edge so debris and water do not splash onto the floor.
  2. Lift out a removable stopper or strainer. If it will not lift, work around the edge gently to release hair or soap sealing it against the opening.
  3. For a screw-in stopper, hold it steady and turn it counterclockwise until it comes free. Stop if it turns without loosening; do not force it.
  4. Use gloved fingers, a plastic card, or a soft brush to pull out hair and soap. Keep small objects in the bucket so you can see what was blocking the drain.
  5. Check the stopper seating ring and drain flange for residue. Wipe both surfaces clean without scratching the finish.
  6. Run a short burst of hot tap water and watch whether the level drops. If it drains, the opening was the main problem; if it barely changes, continue with the next step.

For a pop-up stopper

A pop-up stopper often catches at one edge. Release only the edge that moves, pull the stopper straight up, and disconnect its small linkage if the cap stays behind. Do not yank on the rod or force the mechanism.

For a trip-lever stopper

With a trip-lever assembly, remove only the stopper at the drain if it lifts out. Leave the overflow rod and linkage in place until you test the assembly again in Step 7.

How to tell it worked: The tub empties faster, the stopper sits clear of the opening, and you no longer pull out a mat of hair at the drain. If the stopper still blocks the opening, adjust or replace it in Step 7.

Step 2 Clear the overflow opening

The overflow can collect hair, soap, and small debris even though it is not the main drain. A blocked overflow can hold dirty water behind the cover, create an odor, and prevent a plunger from sealing the tub. Clearing it also gives you access to some drum-style traps.

  1. Let the tub drain as much as possible without forcing water through the blockage. Keep the bucket and towels in place.
  2. Find the overflow cover near the upper end of the tub. Look for a removable metal or plastic plate held in place by friction, clips, or screws.
  3. If the cover lifts out, pull it straight away from the tub. If screws hold it in place, remove the screws carefully and keep them with the cover.
  4. Use a soft brush or flexible cleaning tool to pull out hair and soap from the opening. Do not force a long, rigid object into the tube.
  5. Inspect the recessed area and remove any visible debris. Rinse the opening with hot tap water if the water can reach it.
  6. Keep the overflow cover nearby but leave it off while you plunge. If the cover uses a rubber gasket, protect the gasket from damage while it is removed.

For an overflow with a hair catcher

Some overflow plates contain a removable mesh basket or screen. Take the basket out, empty it, rinse it, and clean the opening around it before reinstalling the plate.

How to tell it worked: Water poured into the overflow opening should enter without resistance, and the plate should sit flush without a gap. Clean overflow openings help the tub drain safely during a backup, but they do not replace clearing the main drain.

Step 3 Plunge the drain with a flange plunger

A flange plunger can move a blockage without pushing it deeper. Its rubber rim seals against the drain opening so that pressure and suction pull trapped material back toward the tub. A cup plunger may not seal against a tub drain, so use a flange-style plunger when possible.

  1. Make sure the stopper and strainer are removed and the overflow opening is clear.
  2. If the tub is empty, add hot tap water until the plunger’s cup is covered. Do not use boiling water.
  3. Center the flange over the drain and press it down firmly. The rim should sit flat against the drain surround with no gap around the edge.
  4. Cover the overflow opening with a clean, wet sponge and hold it firmly in place. Do not allow the sponge to fall into the tub.
  5. Push the plunger down slowly to expel trapped air, then pull it up sharply without breaking the seal. Repeat with a steady rhythm.
  6. After several strokes, pull the flange away and let the water move toward the drain. Watch whether the level falls normally.
  7. If the first attempt does not help, check the flange for folds or debris, reset the seal, and try again. Remove the plunger afterward so it cannot fall into the drain.

If the plunger keeps losing its seal

Dry the rim, reposition the flange, and press it down again. If the cup cannot cover the entire opening, use a rubber stopper that fits completely over the drain. Keep one hand on the overflow sponge so it stays in place.

How to tell it worked: Water begins moving during the plunging, the tub drains more completely, and the gurgling sound stops or becomes less frequent. If water remains motionless, move to Step 4 before trying a snake.

Step 4 Flush the line with hot water and dish soap

Hot tap water can loosen residue, while dish soap helps break up greasy soap film on the drain walls. This method works best when the blockage is light or the trap still has some open flow. It will not remove a tightly packed plug of hair.

  1. Remove any loose hair or debris from the drain opening and confirm that the stopper is out of the way.
  2. Run hot tap water until it becomes hot. Pour the water directly into the drain opening, but do not use boiling water.
  3. Add a small amount of ordinary dish soap to the running water. Do not add bleach, drain cleaner, vinegar, or another household chemical.
  4. Let the mixture sit for several minutes so it can work on soap and grease buildup.
  5. Run more hot tap water to carry the loosened material through the trap. Watch the water level as it drains.
  6. Stop if the tub begins to overflow. Do not keep adding water to a drain that does not move.

If a chemical drain opener has already been used, do not add dish soap or another cleaner, and do not plunge until you have followed the product’s required waiting period and directions. Ventilate the room. If you are unsure what is in the drain, stop and call a plumber.

How to tell it worked: The water level drops steadily and the tub drains without gurgling. If the level barely changes after the flush, use a drain snake next.

Step 5 Send a drain snake through the blockage

A tub drain snake can reach hair and debris that form deeper in the trap or branch line. Turn the cable carefully so its tip hooks the obstruction instead of driving it farther away. The main rule is to stop when the snake meets firm resistance.

  1. Place the bucket under the drain, remove the stopper, and clear the overflow cover if the snake needs a direct path.
  2. Feed the snake cable into the drain opening while keeping control of the cable at all times.
  3. Advance the cable until you feel resistance. Stop cranking as soon as the tip catches something.
  4. Rotate the snake handle while maintaining light pressure on the cable. Keep turning only while the tip stays engaged with the obstruction.
  5. If the cable begins to twist tightly or jam, stop turning. Pull it back slowly and remove the debris caught near the tip.
  6. Rinse the cable and the drain opening, then make another pass if the obstruction has broken apart but the drain still runs slowly.
  7. Never force the cable past a hard stop. Forcing it can twist the cable, scratch old pipes, or push the blockage into another section of the drain.
  8. If the snake stops in the trap or cannot pass the bend, stop and check the accessible trap in Step 6.

If the snake catches near the drain opening

Pull the cable back until you can see the debris. This often means a layer of hair is wrapped around the stopper seat. Clear it, flush the drain, and try the snake again only if the water still moves slowly.

If the snake stops inside the trap

A hard stop may be the trap bend or packed debris. Do not apply more force. Clean an accessible trap in Step 6, or stop and call a plumber if the trap cannot be reached.

How to tell it worked: The snake brings out hair or debris, and the tub drains more freely afterward. If you retrieve no material and see no improvement, the blockage may be deeper than the branch line you can safely reach.

Step 6 Clean the accessible drain trap

The trap holds water to block sewer gases, but it can also catch hair, soap, and small objects. Cleaning it removes material that a plunger or snake may only move back and forth. Bathtubs may use a removable P-trap or a drum-style trap behind the overflow cover, so identify the shape before taking anything apart.

For a removable P-trap

A P-trap has a curved section that can be removed after its slip nuts are loosened. Support the trapped water and fittings so you do not drop them or crack the pipe.

For a drum-style tub trap

A drum trap may sit behind the overflow opening or below the tub. Remove only the cover or insert designed for that trap, and check the opening for a removable basket or plug.

  1. Stop if you cannot clearly identify the trap or its fasteners. An unfamiliar assembly may be part of the supply or another drain line.
  2. Let as much water as possible leave the tub, then place a bucket directly below the trap or overflow opening.
  3. Remove a removable access panel below the tub if one exists. Keep the panel and its screws together.
  4. For a P-trap, support the pipe, loosen the slip nuts with pliers, and remove only the curved trap section. Do not remove supply fittings or the drain valve.
  5. For a drum-style trap, remove the intended cover, basket, or plug and pull out the collected debris without forcing the parts.
  6. Rinse the trap section or drum with hot tap water. Check the removed parts for hair, soap film, corrosion, cracks, or a damaged gasket.
  7. Reinstall the clean parts in the correct order. Tighten slip nuts by hand, then snug them with pliers. Do not wrap ordinary pipe tape around slip-joint connections.
  8. Replace the access panel, restore the overflow cover, and wipe the area under the tub. Check again for drips after water runs through the drain.

How to tell it worked: Water leaves the tub promptly, the trap holds water without leaking, and the area beneath the tub stays dry. If the trap is corroded, cracked, or cannot be reached, do not force it; call a plumber.

Step 7 Restore the drain assembly and confirm drainage

A loose, misaligned, or damaged component can keep a drain partly closed even after the clog is gone. Reassemble the stopper and overflow correctly so the tub drains fully but still holds water when you want it to.

  1. Rinse and dry the stopper, drain flange, overflow plate, linkage, and any removable strainer.
  2. Seat the stopper or strainer in the same orientation it used before removal. Do not force it past the drain opening.
  3. For a pop-up assembly, reconnect the cap to its rod and confirm that the linkage moves freely.
  4. For a trip-lever assembly, align the overflow rod and drain stopper linkage so the stopper opens and closes fully.
  5. Reinstall the overflow plate and any gasket. Tighten removable screws evenly without crushing the plate.
  6. Run water into the tub and confirm that it drains through the opening. Check beneath the tub for drips and watch the overflow during the test.
  7. Replace a cracked stopper, missing gasket, or broken linkage with a matching part. Take the old part with you so the replacement fits.

If the tub drains but will not hold water

That is a stopper or overflow-seal problem rather than a clogged drain. Check the stopper seating ring, linkage, and rubber gasket before assuming the drain line is blocked.

How to tell it worked: The tub empties smoothly, the overflow remains quiet during normal draining, the stopper seals when closed, and no water leaks beneath the tub.

Symptom checker

What you notice Likely cause Fix (step number)
Water drains a short distance and stops Hair or an object at the drain opening 1
Water barely moves Full opening or a deeper blockage 1, 3, 5
The tub gurgles as water leaves Partial blockage and trapped air 5
The overflow backs up or holds debris Clogged overflow opening 2
The stopper will not open Buildup or damaged linkage 1, 7
The snake catches near the opening Hair mat around the stopper seat 1, 5
The snake stops at the trap Packed or obstructed trap 6
The clog returns soon after cleaning Residue in the trap or a deeper branch problem 4, 6
Several drains are slow or sewage backs up Main drain or sewer problem 5–6, then call a professional
Water drains, but the tub will not hold it Stopper or overflow seal issue 7

Mistakes that make it worse

  • Pouring boiling water into the tub, which can soften some pipes, damage seals, or stress older plumbing.
  • Mixing bleach, vinegar, ammonia, dish soap, or drain cleaners, which can create dangerous fumes.
  • Forcing a snake past resistance, which can kink the cable or push the blockage deeper.
  • Using a sharp wire or tool to probe the drain, which can scratch the pipe or damage a seal.
  • Leaving the stopper, overflow plate, or linkage loosely reassembled, which can cause leaks or a partial blockage.
  • Continuing to add water when the tub will not drain, which can cause overflow and property damage.

When to call a professional

  • Call a licensed plumber if the snake cannot pass through the trap or if cleaning the accessible trap does not restore flow.
  • Call a plumber if the clog returns repeatedly even after the stopper, overflow, and trap are clean.
  • Call a plumber if several fixtures drain slowly, sewage backs up, or dirty water rises into the tub.
  • Call a plumber if you find a leak, corroded fittings, cracked pipes, a damaged drain valve, or a trap that cannot be removed safely.
  • Call a plumber if the drain or overflow must be replaced, the trap is inaccessible, or the blockage lies beyond the branch line.

How to keep it from happening again

  • Use a drain hair catcher and empty it often so hair does not reach the opening.
  • Pull loose hair away from the drain before bathing or showering.
  • Run hot tap water after use to carry small amounts of soap and residue away.
  • Clean the overflow opening and its hair catcher as part of regular bathroom care.
  • Keep bath toys, loose objects, oily products, and wipes out of the drain.
  • Arrange routine trap cleaning if clogs recur often and the trap is safely accessible.

Frequently asked questions

Can baking soda and vinegar unclog a bathtub drain?

Baking soda alone is unlikely to remove a mat of hair. Vinegar can react with bleach or other drain chemicals, so do not mix it with anything. Use the plunger and snake methods instead.

Do I need a special plunger for a bathtub?

A flange plunger is best because its rim can seal over the drain opening. A cup plunger may not create enough suction. Cover the overflow opening with a wet sponge while you plunge.

Why does my tub gurgle after I run the shower?

A gurgle often means a partial blockage is trapping air as water moves past it. Clear the stopper and overflow, then try plunging before using a drain snake.

Should I remove the overflow plate?

Remove it when you need to clean the opening, reach a drum-style trap, or seal the overflow for plunging. Keep the plate, screws, and gasket together, and reinstall them after testing.

Are chemical drain openers safe for tubs?

Chemical openers can create fumes, splash caustic material, and damage some plumbing. Avoid mixing them with other products or using them before mechanical cleaning. If you have already used one, follow its label and wait the required time before handling the drain.

When should I stop and call a plumber?

Stop if the snake will not pass, the trap is inaccessible, or repeated cleaning does not help. Call a plumber for sewage backups, leaks, corroded fittings, damaged drain parts, or slow drains throughout the home.

What this guide is based on

Revision history

  1. Updated and re-checked against sources.
  2. First published.

Did this fix it?

Mixtvnowcom.org editors Editorial team

The Mixtvnowcom.org editors write and check every guide on the site against the manufacturer instructions and official sources it lists, and keep each guide's revision history up to date.

More guides from the editors