On this page

Quick answer

The most common causes are a kinked or clogged drain hose, a blocked pump filter, or a failed drain pump. Start by stopping the cycle, unplugging the washer, and checking the hose and filter. If those are clear, test the pump and check for a blocked sump or control fault.

At a glance

Time
15–45 min
Difficulty
Moderate
You'll need
Flashlight, towels, shallow container, basic hand tools
Cost
Free for most fixes; a part if one is worn
Works on
Top-load and front-load washing machines
Not covered
internal wiring, or sealed pump repairs

Why is my washing machine not draining?

A washing machine normally moves water from the tub through a drain pump and filter, then sends it through a drain hose to a standpipe or floor drain. The filter is intended to catch lint, coins, hairpins, and other debris before they reach the pump. If the water cannot leave the tub, the washer may stop, pause, or begin refilling while the clothes remain wet.

Common causes include a bent or crushed drain hose, debris packed around the pump impeller, a clogged pump filter, or a hose that is routed incorrectly. A damaged drain pump, failed drive, or electrical or control fault can produce the same symptom. If you open the door and find the washing machine full of water, stop the cycle and drain or isolate that water before inspecting the parts.

When a washer won’t drain or spin, watch both symptoms during a test. It may drain normally but fail to spin because the load is unbalanced or the door or lid is not fully closed. It may also stop with water inside when the pump, door lock, or control system does not respond. Start with the hose and filter because those are the easiest items to check and the most common places for a blockage.

Before you start

Turn off power before opening the filter, a hose connection, an access panel, or any area near moving parts. Unplug the washer or switch off its breaker. Restore power only after everything is dry, reassembled, and clear of the drum.

Let standing water cool before handling it. Put towels and a shallow container below the filter so you can control water that escapes. If you must move the washer or disconnect a fill hose, close the hot and cold supply valves first. Reopen them after the washer is in position and the connections are dry.

Do not remove covers that expose internal wiring. Those jobs also require a qualified professional.

  • Keep the washer model manual open, especially for the filter location, emergency drain procedure, and cycle controls.
  • Use a flashlight, dry towels, a shallow bowl or low-sided container, and basic hand tools.
  • Wear closed-toe shoes and gloves, and keep the floor around the washer dry.

Do not open a pump filter while the washer is plugged in, while the drum is moving, or while hot water is above the filter. Water can spill suddenly and may scald.

Step 1 Stop the cycle and drain standing water safely

Why this helps: A full tub makes the filter, pump, and hose harder to reach. Stopping the wash removes power from the drain system, and controlled draining prevents water from spilling across the floor.

  1. Press Pause, Cancel, or the cycle-end control. Wait for the drum and pump to stop before opening anything.
  2. If the door remains locked, allow the control to release it. Do not force the door open or insert a tool into the latch.
  3. Unplug the washer or switch off its breaker. Keep it off until the filter or hose work is finished.
  4. Let the remaining water cool. Move towels beneath the filter area and place a shallow container where you can set the filter without spilling water.
  5. Locate the drain pump filter using the manual. On many front-load washers it sits behind a small lower access door; on some top-load washers it is near the front or lower rear. Do not confuse it with a tub lint filter.
  6. If water remains above the filter, use the emergency drain hose supplied with the washer only if the manual explains how to connect and use it. Place the supplied container lower than the tub and let the water flow out slowly.
  7. If no safe emergency drain method is accessible, do not pull the washer forward or tip it over. Moving it can damage the hose, spill water near electrical parts, or shift the machine.
  8. Once the water level is below the filter opening, you can inspect and clean the filter using Step 3.

How to tell whether it worked

The water level should fall enough to expose the filter area, and the door should release normally if it was held by the cycle. If water still sits above the filter, stop and arrange service rather than opening the cap during an uncontrolled spill.

Step 2 Straighten and check the drain hose

Why this helps: A drain hose can kink behind the washer, collapse under the machine, fill with lint, or form a loop that lets water flow back toward the tub. A hose pushed loosely into a standpipe can also come out during the drain cycle.

  1. With the washer unplugged or its breaker off, place a bucket or container beneath the hose connection at the standpipe or floor drain.
  2. Disconnect the drain hose from the standpipe or drain inlet. Note how it was routed before removing it.
  3. Inspect the entire hose for sharp bends, crushing, cracks, loose fittings, lint, slime, or objects lodged near the outlet.
  4. Straighten the hose gently. If it is clear, rinse it slowly with plain water and check that water can pass through without forcing debris farther inside.
  5. Inspect the standpipe or floor drain opening. Remove only debris that is loose and easy to reach, and do not drop tools into the drain.
  6. Reconnect the hose and secure it so it cannot slip out during a cycle. Do not force the hose so deeply into the standpipe that it seals against the pipe or creates a tight bend.
  7. Check the hose height. The manual should control how high the hose sits and how it is secured. A low loop below the tub can let water drain back instead of flowing out.
  8. Restore power and run the shortest drain or rinse cycle available. Listen for the pump and watch the water level while the hose remains connected.

How to tell whether it worked

The tub should empty steadily, and water should leave through the hose without gurgling back into the washer. If the pump runs but water remains, the hose may still be restricted or the blockage may be inside the washer.

Step 3 Clean the drain pump filter

Why this helps: The pump filter catches lint, coins, hairpins, and other debris before the water reaches the impeller. A clogged filter can make the pump noisy, slow, or unable to move any water.

  1. Confirm the washer is unplugged or its breaker is off. Make sure the water is cool and place your container and towels below the filter.
  2. Find the actual drain pump filter in the model manual. A removable lint screen in a tub or dryer is a different part and will not clear the pump.
  3. Open the lower access door or cover, if the washer has one. Do not remove a panel that exposes wiring, belts, or other internal components.
  4. Remove the filter cap in the direction shown by the manual. Many caps turn counterclockwise, but the design varies. Let the pressure release slowly so water does not rush onto the floor.
  5. Remove lint, coins, and other debris from the filter. If the filter comes out, rinse it under lukewarm water and check that its passages are open.
  6. Use your fingers or a soft brush to clean the visible filter housing. Do not push a sharp tool into the pump or twist the impeller by hand.
  7. Check the filter seal or gasket, if present. Make sure it is clean, seated correctly, and not torn before reinstalling the filter.
  8. Reinstall the filter snugly according to the manual, close the access door, and run a short drain test.

If your washer has no user-accessible pump filter

Some models place the pump behind a sealed panel or beneath the tub. Do not remove the tub, pump housing, or sealed covers yourself. Continue with the pump test in Step 4 and arrange service if the pump does not move water.

How to tell whether it worked

The pump should run more quietly and the tub should drain more quickly. If the filter held heavy debris, clean the housing and hose again before assuming the pump has failed.

Step 4 Check whether the drain pump runs

Why this helps: Clearing the hose and filter confirms that the drain path is open. If the pump still does not start, move the water, or run continuously, the remaining problem is likely the pump, its drive, or the control that starts it.

  1. Reassemble the filter, access door, and hoses completely. Wipe away spilled water and make sure no tool or cloth is near the tub or pump.
  2. Restore power by plugging in the washer or switching on the breaker. Select a short drain cycle, a drain-and-spin cycle, or a small-load cycle if the washer has no drain-only setting.
  3. Stand clear of the moving tub and listen near the base of the washer. A working drain pump normally produces a brief hum or motor sound as it starts.
  4. If you hear no motor sound, consult the manual for a pump-test procedure and repeat the power reset in Step 6. Do not open the control panel or test terminals yourself.
  5. If the pump hums but no water moves, recheck the filter, hose, and visible pump opening. A jammed impeller or failed pump can produce this sound.
  6. If the pump hums continuously without lowering the water level, stop the cycle and disconnect power. Do not leave the pump running against a blockage.
  7. If water moves but drains very slowly, check the hose again for a soft blockage, a sharp bend, or a sink or standpipe that cannot accept water as quickly as the pump sends it.
  8. Write down what you hear and see, including whether the pump hums, the tub stays full, and the drain hose receives water. Those details help a technician narrow the fault.

Top-loader belt-driven pump variation

Some top-load washers use a belt to drive the drain pump, while others use a direct-drive motor. If your manual shows a belt-driven pump and permits access, switch off the breaker before inspecting an exposed belt. Replace or adjust a loose or damaged belt only if the manual gives clear instructions; otherwise, have a technician handle it.

How to tell whether it worked

A successful test includes pump operation, falling water in the tub, and water leaving through the hose. If the pump runs but the tub remains full, the fault is downstream or inside the pump. If the pump does not run at all, the pump, motor, drive, or control needs further diagnosis.

Step 5 Clear a blockage in the sump or pump inlet

Why this helps: Objects can become trapped between the tub and the pump. Cleaning only the filter may not help if the inlet hose, pump throat, or sump remains blocked.

  1. Turn off the power again, let any water cool, and drain enough water to expose the filter and lower pump area safely.
  2. Use a flashlight through the filter opening and look for lint, coins, clips, or other objects that are visible and easy to remove.
  3. Remove only objects you can grasp without pushing them deeper. Do not use a screwdriver to poke the impeller or pull an object out of a hidden housing.
  4. Check the visible pump throat and the hose leading into the pump for a blockage. If you cannot see the area clearly, do not force a tool into it.
  5. If the manual identifies an accessible debris filter, remove it only as directed and rinse away loose lint. Do not soak a filter that contains a sealed component.
  6. After cleaning, replace any filter or cap you removed. Close the access panel, wipe the area dry, and check that the hose and panel do not interfere with the tub.
  7. Restore power and run a drain test. Watch both the tub and the drain hose so a partial flow does not look like a complete drain.

Front-loader variation

Some front-load washers have a removable sump hose between the tub and pump. If the manual identifies it as user accessible, disconnect the clamp only after removing power, inspect the hose, and reconnect it securely. If the panel exposes wiring or the clamp is difficult to release, stop and call a technician.

Top-loader variation

Top-load washers often route water from the tub into a pump beneath the tub. That area is usually not intended for owner access. Clear only what you can reach through the filter opening; do not lift the tub or remove the pump yourself.

How to tell whether it worked

The tub should empty in a steady flow and stay empty. If the pump hums, water reaches the pump, but the hose does not discharge, call for service. The remaining obstruction is probably inside the sealed drain path.

Step 6 Reset the washer and run a drain test

Why this helps: A paused cycle, active child lock, delayed start, or door-lock state can prevent the drain from beginning. A brief power reset may clear the control without affecting a simple blockage, but it will not repair a damaged pump.

  1. Press Pause or Cancel and wait until the drum stops. Do not repeatedly press controls while the washer is moving.
  2. Check the control panel for a paused indicator, child lock, delayed start, or door-lock message. Release the child lock with the manual’s control and make sure the door or lid is fully closed.
  3. Confirm that the filter door and any lower access cover are closed. A safety interlock may prevent a cycle from starting while a cover is open.
  4. Unplug the washer or switch off its breaker. After a few minutes, plug it back in or restore the breaker.
  5. Choose a short drain, drain-and-spin, or rinse-and-spin cycle according to the available controls. Do not select a delayed start.
  6. Watch the tub during the first part of the cycle. You should hear the pump when draining begins, and the water level should fall.
  7. If the washer begins draining but pauses before spinning, move to Step 7 and check the load and door or lid latch.

Keep the washer door closed during the test. If the door lock does not click or the lock indicator never changes, do not force the latch or bypass the switch.

How to tell whether it worked

The washer should drain without being restarted and should complete the selected cycle. If the same pause returns after every reset, record the control message or indicator pattern without guessing an error code and contact a technician.

Step 7 Correct an unbalanced load and check the spin

Why this helps: A washer may stop and redraw water when it cannot balance the load for a spin. Separating drain and spin symptoms helps you avoid replacing a pump when the drain works and only the spin is failing.

  1. Stop the cycle if the washer is repeatedly filling, draining, and pausing. Pause or cancel it before opening the door.
  2. For a front-load washer, remove wet items one at a time and spread them loosely around the drum. Do not leave a heavy item twisted into a tight bundle.
  3. For a top-load washer, distribute the items around the tub and avoid packing the center so tightly that the load cannot settle.
  4. Reduce the load to the amount stated in the manual. Separate unusually heavy items from lighter clothing and towels.
  5. Close the door or lid fully and select a spin-only cycle if the washer offers one. Otherwise, use the shortest cycle with a small, evenly distributed load.
  6. Watch the drum through the glass or open a top-loader only after the drum has stopped. The drum should rotate steadily rather than repeatedly stop and reverse.
  7. If the washer drains but the drum never rotates, stop testing. A failed door switch, motor, drive belt, brake, or control may be preventing the spin.

Front-loader door-lock variation

A front-load washer normally will not release the door while the water level is unsafe or the drum is moving. If the door releases normally but the machine refuses to start or spin, the lock, switch, or control may need service.

Top-loader lid variation

A top-load washer may pause during an unbalanced spin and restart with water. If the lid switch does not register as closed, the washer may not enter the spin or drain sequence. Do not hold the lid switch down as a permanent bypass.

How to tell whether it worked

The water should drain, the drum should rotate, and the cycle should continue. If the washer drains normally but will not spin under a small, balanced load, the drain path is working and the spin drive or control needs professional diagnosis.

Symptom checker

What you notice Likely cause Fix (step number)
The tub is still full after the cycle Blocked hose, clogged filter, failed pump, or inactive control Steps 2, 3, 4, and 6
Water drains very slowly Partial hose blockage or partly clogged filter Steps 2 and 3
The pump hums but no water leaves Jammed impeller, pump failure, or sump blockage Steps 3, 4, and 5
There is no pump sound and water remains Pump, motor, drive, or control fault Steps 4 and 6
The washer drains but the drum will not spin Unbalanced load, door or lid switch, or drive fault Step 7
The washer won’t drain or spin after repeated pauses Control state, unbalanced load, or safety interlock Steps 6 and 7
Water appears in the hose or returns to the tub Incorrect hose routing or a drainback loop Step 2
Lint or coins appear at the filter opening Debris collected in the pump area Steps 3 and 5

Mistakes that make it worse

  • Opening the filter while the washer is powered, moving, or filled with hot water above the filter.
  • Pouring boiling water or harsh chemical cleaner into the pump or drain hose.
  • Prying on the filter cap or poking a sharp tool into the impeller and damaging the pump housing.
  • Forcing the drain hose into the standpipe, creating a sharp bend, or leaving it unsecured.
  • Forcing the door open, holding a lid switch down, or bypassing a safety interlock.
  • Continuing repeated heavy cycles with an overloaded or unevenly distributed load.

When to call a professional

  • The pump does not run after you clean the filter, clear the hose, and reset the control.
  • The pump runs but cannot move water, and the blockage is inside a sealed sump or pump housing.
  • Water leaks from the filter housing, drain hose, pump, or tub after your checks.
  • You notice a burning smell, sparks, unusual heat, or a breaker trip. Unplug the washer or switch off the breaker and call a licensed electrician or qualified appliance technician; do not open internal wiring panels.
  • The washer drains but the drum will not spin, or you suspect the motor, belt, brake, door lock, or control has failed.
  • The washer must be tilted, moved through a narrow opening, or opened far enough to expose the tub, drive, or sealed pump assembly.

How to keep it from happening again

  • Clean the drain pump filter on the schedule in the washer manual, and more often if you wash linty towels or clothing.
  • Inspect the drain hose for kinks, loose connections, and trapped debris before each long wash.
  • Keep laundry out of the door seal and avoid overloading the washer.
  • Secure the drain hose according to the manual so it cannot slip out or form a low loop.
  • Wipe up spills promptly and check beneath the washer for leaks, lint, or standing water.

Frequently asked questions

Why is my washing machine full of water after the cycle?

A drain hose, pump filter, pump, or control problem can leave water in the tub. Pause or cancel the cycle and use the filter or emergency drain only as the manual describes. If you cannot drain it safely, stop and call a technician.

Where is the drain pump filter?

Many front-load washers place it behind a lower access door, while some top-load washers have one near the front or rear. The model manual is the best guide. A lint filter is not the same as the drain pump filter.

Is it safe to open the pump filter?

Only after unplugging the washer or switching off its breaker and allowing the water to cool. Place towels and a shallow container below it. If water sits above the filter, do not open the cap.

Why is my washing machine draining slowly?

A partially clogged filter or a bent drain hose is the usual place to look. Debris in the sump can also slow the flow. Clean the accessible filter and inspect the full hose before testing the pump.

Why won't my washer drain or spin?

An unbalanced load can stop the spin and cause the washer to pause. A blocked drain path, failed pump, door-lock problem, or control fault can also stop both functions. Reset the control, distribute the load, and test the drain separately.

Do I need a technician if the pump does not hum?

First clear the filter and hose, then repeat the power reset and drain test. If the pump remains silent, the pump, motor, drive, or control may be faulty. A technician can test those parts safely.

What this guide is based on

Revision history

  1. Updated and re-checked against sources.
  2. First published.

Did this fix it?

Mixtvnowcom.org editors Editorial team

The Mixtvnowcom.org editors write and check every guide on the site against the manufacturer instructions and official sources it lists, and keep each guide's revision history up to date.

More guides from the editors