On this page
Quick answer
A dryer that is completely dead often has an open breaker, tripped outlet, loose plug, or failed power cord. If the display or drum light works but the drum will not start, check the door latch, control lock, selected cycle, and excessive load. Unplug the dryer or switch off its breaker before inspection, then restore power and test a cycle.
At a glance
- Time
- 20–60 min
- Difficulty
- Moderate
- You'll need
- Flashlight, outlet tester, owner’s manual, dry cloth
- Cost
- Free for most checks; parts or service may be needed
- Works on
- Electric and gas dryers; top-load and front-load models
- Not covered
- Gas repairs, internal wiring, or heating-only faults
Why is my dryer not turning on?
A dryer must complete a short chain before the drum moves: the outlet supplies power, the controls confirm that the door is closed and a cycle is selected, and the start circuit sends power to the motor. If one part of that chain fails, the dryer may look completely dead or may light up but remain still. A loose plug or tripped breaker is common, while a failed door switch, thermal fuse, start switch, motor, belt, or control board is also possible.
“Not turning on” can describe two different problems. With no power, you will usually see no lights, no display, and no response to the start button. With power but no start, the drum light or display may work, but the cycle will not begin or the motor will not turn. These symptoms lead to different checks, so do not replace a part until you know whether the failure is in the power supply, controls, or motor circuit.
A blocked lint screen or dirty vent usually affects drying and heat rather than the start command. Some dryers, however, stop after overheating, so a clean lint screen is still an early check. If the drum turns but the dryer does not heat, that is a separate fault and is not the main problem covered in this guide.
Before you start
Safety first: Switch off the dryer’s breaker and unplug the appliance before you inspect the plug, outlet, door latch, lint screen, or drum. Do not remove the control panel or rear panel while the dryer is connected. If you smell gas, leave the area without operating switches or starting the dryer, then call the gas utility’s emergency line from outside. Do not work on the gas line, valve, or burner.
Have the owner’s manual, a flashlight, a plug-in outlet tester, a dry cloth, and a soft brush ready. Find the dryer’s model and serial number without removing any panels. Also note whether it is top-loading or front-loading and whether it uses gas or electricity, because the door and control arrangements differ.
- Clear the area around the dryer so you can reach the plug, vent, and door.
- Use a dry, well-lit work area.
- Keep the lint screen and lint trap dry before reinstalling them.
- Do not bypass a door switch, thermal fuse, control lock, or other safety device.
A dryer that is completely dead and a dryer whose lights work but whose drum does not move need different checks. Watch which symptom occurs before changing any settings.
Step 1 Check the outlet and circuit breaker
Why this helps: If the dryer has no lights or display, begin at the wall. A tripped breaker or an outlet that no longer supplies power can stop everything downstream, including the controls and motor.
- Switch off the breaker serving the dryer and unplug the dryer by gripping the plug, not the cord.
- Look at the outlet face and plug from a safe distance. Stop if you see moisture, melting, discoloration, a burned smell, or a hot plug. Do not reconnect the dryer.
- Restore the breaker. If it stays on, check the outlet with an outlet tester while the dryer remains unplugged. Do not remove the outlet cover or touch exposed wiring.
- If the tester shows that the outlet has power, plug the dryer directly into that outlet. Do not use an extension cord, adapter, or power strip unless the owner’s manual specifically permits it.
- If the breaker trips again, switch it off, leave the dryer unplugged, and stop resetting it. A repeated trip points to an electrical fault that needs professional attention.
- If the outlet has a ground-fault reset, follow the instructions printed on the outlet. Keep the dryer unplugged while checking the outlet.
How to tell it worked: The outlet tester confirms power, and the dryer’s display, drum light, or buttons respond after the dryer is plugged in. If the outlet has no power or the breaker trips again, continue without plugging in the dryer.
Step 2 Reset the dryer and release any control lock
Why this helps: A brief power interruption can leave electronic controls paused, locked, or waiting for a response. A full power reset clears that condition without opening the appliance.
- Switch off the breaker and unplug the dryer.
- Leave the dryer disconnected for several minutes.
- Make sure the plug and outlet are dry and at room temperature. Reconnect the plug directly to the outlet, then restore the breaker.
- Close the door fully. Select a normal timed or automatic cycle as described in the owner’s manual.
- Check the display and panel for a control-lock, child-lock, pause, or door indicator. Release the lock using the button or control named in the manual.
- Press the start control or turn the timer as the manual directs. If the start control must be held down, hold it only as long as the manual instructs.
Control-lock controls vary
The lock may be a separate button, a long press of the start control, or a combination described on the panel. Do not guess if the symbols differ from the manual. If the lock indicator remains on after you use the documented procedure, continue with the door and start-circuit checks.
How to tell it worked: The display responds, the lock or pause indicator clears, and the dryer begins its selected cycle. If the panel stays blank, move to the outlet and power-cord checks.
Step 3 Make sure the door closes and the latch engages
Why this helps: Most dryers use a door switch or electronic lock to confirm that the drum is safe before the motor starts. A door that does not close fully, a blocked latch, or a loose switch can prevent the start command from working.
- Switch off the breaker and unplug the dryer.
- Open the door and inspect the visible door opening, gasket, and latch area for clothing, lint, coins, or other debris.
- Remove any item that is blocking the latch without pushing your fingers past the visible edge of the drum opening.
- Close the door firmly. It should sit flush against the cabinet without being forced.
- For a front-loader, listen and watch for the normal latch or lock indication. Do not pry the latch, release an electronic lock, or remove a panel.
- Reconnect the dryer, restore power, select a normal cycle, and try the start control again.
Top-load and front-load differences
On a top-loader, check that the door does not hit the cabinet or frame when closed. On a front-loader, check that the visible latch opening is not blocked and that the door closes without being pushed past its normal stop.
How to tell it worked: The door now closes without obstruction, the lock indicator behaves normally, and the motor starts. If the latch feels loose, does not click when it should, or remains locked, arrange appliance service.
Step 4 Set and start a valid cycle correctly
Why this helps: Selecting a cycle is not always enough on models with electronic controls. The dryer may still be paused, stopped, waiting for the door, or waiting for a held start command.
- Close the door and check the display for a paused, stopped, locked, or waiting message.
- Move the timer or program selector away from its off position and choose a normal timed or automatic drying cycle.
- Press the start, start/pause, or rotary start control. Do not merely move the selector and wait.
- If the control panel shows an error, read the exact wording and find it in the owner’s manual. Do not assume every model uses the same message or reset procedure.
- Follow any on-screen prompt for loading, door closure, sensor cleaning, or control release. Do not bypass the prompt.
- If the timer begins counting down but the drum stays still, note that behavior and continue to the motor and start-circuit checks.
How to tell it worked: The selected cycle remains active and the drum starts moving. A countdown with no drum movement means the controls and power are working, but the motor is not being started.
Step 5 Clean the lint screen and check its housing
Why this helps: A dirty lint screen usually slows drying, but it can also restrict airflow enough for some models to shut down after overheating. Cleaning it is quick, safe, and worth doing before more involved checks.
- Switch off the breaker and unplug the dryer.
- Locate the lint screen and remove it carefully so you do not bend or tear the screen.
- Peel accumulated lint away by hand and place it away from heat or flame. Do not push lint deeper into the dryer.
- Use a dry cloth or soft brush to clean the visible screen housing and the area around the opening.
- Wash the screen only if the owner’s manual says it is washable. If you wash it, let it dry completely before reinstalling it.
- Reinstall the screen fully, reconnect the dryer, restore power, and start a normal cycle.
Lint-screen locations
The lint screen is commonly inside the door opening on a front-loader or in a panel near the door on a top-loader. Its exact location and removal method can vary, so follow the manual if the screen does not match the usual location.
How to tell it worked: The screen is clean, fully seated, and the dryer starts normally. If the dryer still will not start, cleaning the screen did not identify the failure, so continue to the remaining checks.
Step 6 Remove excess laundry and check for a stopped drum
Why this helps: An overloaded drum can prevent the door from latching, stop the drum from moving, or overload the motor. A trapped clothing item can also block a roller or pulley.
- Let the current cycle stop, switch off the breaker, and unplug the dryer.
- Remove all laundry from the drum, including items caught in the door gasket or the visible drum opening.
- Turn the drum gently by hand. Do not force it and do not use a tool to move it.
- If the drum does not turn easily, stop. Do not dismantle the dryer to reach the obstruction.
- If the drum turns by hand but makes scraping, grinding, or catching sounds, arrange professional service.
- Close the door, reconnect the dryer, restore power, select a normal cycle, and test the empty drum.
How to tell it worked: The empty drum begins rotating normally and the cycle starts. If the dryer works without the load, clean and redistribute the laundry before using it again.
Step 7 Inspect the plug and visible power cord
Why this helps: A loose, overheated, cracked, or partly disconnected plug can make the dryer appear dead. Damaged wiring can also create a serious shock or fire hazard.
- Switch off the breaker before unplugging the dryer. Grip the plug body rather than pulling the cord.
- Inspect the visible plug prongs, plug housing, and cord. Look for looseness, bent prongs, cracks, pinched areas, discoloration, melting, or a burned odor.
- If you find any damage, leave the dryer unplugged. Do not tape the cord, splice wires, or install a replacement plug yourself.
- If the plug and cord are undamaged, reseat the plug firmly in the outlet. Plug the dryer directly into the wall outlet rather than through an extension cord or adapter.
- Use an outlet tester again with the dryer unplugged. If the outlet is powered, reconnect the dryer and test the start control.
- If the plug or outlet becomes warm during operation, switch off the breaker before touching either one. Do not reconnect it until a qualified technician checks it.
How to tell it worked: The plug stays secure and cool, the outlet tester shows normal power, and the dryer responds after it is reconnected. Visible cord or plug damage means the dryer should remain unplugged.
Step 8 Check the electronic door lock on a front-loader
Why this helps: A front-loader may display power and accept your cycle selection while refusing to start because the electronic door lock has not engaged. A failed lock can also click repeatedly without completing the cycle.
- Confirm that you are using a front-loader and note any door-lock indicator on the display or panel.
- Release the control lock and complete the power-reset steps before trying the door again.
- Close the door firmly and listen for the normal locking sound. Depending on the model, the lock may engage when the door closes or when the cycle begins.
- Wait for the lock indicator to change to its normal state. Do not force the handle or try to pry the door open.
- Start the cycle only when the panel indicates that the door is secure.
- If the lock clicks repeatedly, stays locked without a start, or will not release after a power reset, stop using the door and call an appliance technician.
How to tell it worked: The door-lock indicator changes normally and the cycle starts. If the lock mechanism remains engaged or keeps clicking, it needs professional repair.
Step 9 Have the start circuit checked when the symptoms remain
Why this helps: If the outlet has power and the display works but the drum will not start, the problem may be a failed door switch, thermal fuse, start switch, motor, belt, pulley, or control board. Testing those parts involves internal wiring and should be left to a qualified technician.
- Record what happens: whether the display lights, whether the drum light turns on, whether the dryer beeps, and whether the motor hums.
- Run a normal cycle with an empty drum. If the motor hums but the drum remains still, stop the cycle rather than leaving it running.
- Switch off the breaker, unplug the dryer, and check only whether the drum turns easily by hand. Do not put your hand near a moving motor, belt, or pulley.
- Find the model and serial number and write down the exact symptoms, including any message on the display.
- Call a qualified appliance technician and describe the checks you completed. Ask the technician to check the start circuit and any failed component.
- Do not remove the control panel or rear panel, test internal wires, bypass a switch, or replace a thermal fuse yourself.
How to tell it worked: After repair, the door closes securely, the cycle remains active, and the motor turns the drum without unusual noise. A working outlet with a completely blank panel suggests a control or power-input fault that requires bench testing.
Symptom checker
| What you notice | Likely cause | Fix (step number) |
|---|---|---|
| No lights, display, or response | Tripped breaker or inactive outlet | Step 1 |
| Outlet has power but the dryer is blank | Loose or damaged plug, or a control power fault | Steps 7 and 9 |
| Display lights but no cycle begins | Control lock, paused cycle, or door switch | Steps 2, 3, and 4 |
| Front-loader door clicks repeatedly | Door lock or latch problem | Steps 3 and 8 |
| Timer advances but the drum stays still | Start switch, thermal fuse, motor, or belt | Step 9 |
| Motor hums but the drum does not turn | Slipped belt, seized pulley, or motor problem | Step 9 |
| Drum will not turn by hand | Obstruction or seized drum component | Step 6 |
| Loud thumping, scraping, or rattling | Trapped item, loose roller, belt, or pulley | Steps 6 and 9 |
| Dryer starts and then stops | Overload, airflow restriction, or thermal cutoff | Steps 5, 6, and 9 |
| Dryer works after being unplugged and replugged | Loose plug or temporary control state | Steps 1, 2, and 7 |
| Dryer works with an empty drum | Excessive or tangled laundry | Step 6 |
| Breaker trips again when the dryer starts | Electrical fault requiring professional diagnosis | Step 1 |
Mistakes that make it worse
- Resetting a tripped breaker repeatedly. A breaker that trips again needs diagnosis, not repeated attempts to start the dryer.
- Using an extension cord or adapter. This can create an overloaded or loose connection. Plug the dryer directly into a suitable wall outlet.
- Reconnecting a damaged cord or plug. Cracked insulation, melted plastic, heat, or a burned smell requires the dryer to remain unplugged.
- Bypassing a door switch, lock, or thermal fuse. These devices are part of the safety system and should not be jumped for testing.
- Forcing a locked door or removing panels. This can damage the latch, wiring, or control assembly and create a shock risk.
- Running the dryer while ignoring a gas odor or a heating-only complaint. Leave the area and call the gas utility for a gas odor. Treat a dryer that runs without heat as a separate service issue.
When to call a professional
- Call a qualified electrician or appliance technician if the breaker trips again, the outlet is scorched or buzzing, or the plug becomes warm.
- Arrange service if the power cord, plug, outlet, or visible wiring is damaged. Do not splice or repair wiring yourself.
- If you smell gas, leave the area without operating electrical switches and call the gas utility’s emergency line. Gas lines, valves, and burners require a licensed professional.
- Call an appliance technician if the motor hums without turning, the drum turns by hand but not during the cycle, or the dryer makes severe scraping, burning, or belt noises.
- Call for service if a front-loader’s electronic lock stays engaged, clicks continuously, or will not release after a power reset.
- Call a technician if the outlet has power but the panel remains blank, a message persists, the control lock will not clear, or the drum will not start after the basic checks.
- Leave internal wiring, control boards, thermal fuses, motors, switches, belts, and pulleys to qualified professionals. Do not open the control panel or rear panel for these repairs.
How to keep it from happening again
- Clean the lint screen often and follow the owner’s manual for cleaning frequency.
- Keep the dryer floor and the area around the plug dry and clear.
- Load the dryer within the capacity stated in the manual and avoid tightly packing wet laundry.
- Check the visible plug and cord periodically for looseness, cracks, heat, or discoloration.
- Keep the exterior vent opening clear and remove lint before it reaches the duct.
- Plug the dryer directly into a suitable wall outlet, and switch off the breaker before cleaning or inspecting accessible parts.
Frequently asked questions
Why does my dryer have power but won’t start?
If the display or drum light works, check the door, control lock, selected cycle, and load before suspecting a failed motor. A normal cycle that starts counting down but does not move the drum points to the start circuit, belt, or motor and needs professional testing.
Why is my dryer dead even after I reset the breaker?
Do not keep resetting the breaker if it trips again. Test the outlet with the dryer unplugged, and have an electrician check the outlet if it has no power. If the outlet works but the dryer remains blank, the plug, cord, or internal power supply may be at fault.
Does the dryer need to get hot before the drum turns?
No. A dryer normally starts the motor on a cold cycle. If the drum turns but the dryer does not heat, that is a heating-system problem rather than a no-start problem.
Can I replace the thermal fuse or door switch myself?
Do not replace either part yourself because testing them involves internal wiring. Complete the external checks in this guide, then have a qualified appliance technician inspect the components.
Will cleaning the lint screen make the dryer start again?
It can help if restricted airflow caused an overheating shutdown, but a dirty screen more often causes slow or incomplete drying. Clean it as part of troubleshooting, then continue checking the outlet, door, controls, and start circuit if the dryer remains stopped.
What should I do if the dryer hums but the drum does not move?
Stop the cycle, switch off the breaker, and unplug the dryer. Remove any visible trapped laundry and check whether the drum turns easily by hand, but do not open the machine for belt or motor access.
What this guide is based on
- Appliance support geappliances.com
- Dryer support samsung.com
Revision history
- Updated and re-checked against sources.
- First published.
Did this fix it?
Thanks. Glad it's sorted.
Sorry it's still not right. Recheck the symptom checker above, or tell us what you're seeing.