On this page
Quick answer
A dryer usually stops spinning because the drum is overloaded, the door latch or control has not started the cycle, or the belt, idler pulley, drum rollers, or motor has failed. First, unplug the dryer, reduce the load, clean the lint screen, and check the door closes fully. Then listen for the motor and inspect accessible drive parts.
At a glance
- Time
- 20–60 min
- Difficulty
- Moderate
- You'll need
- Dryer manual, flashlight, screwdriver, and safe access
- Cost
- Free for most checks; parts may be needed
- Works on
- Electric or gas belt and direct-drive dryers
- Not covered
- Internal wiring, burner service, or vent installation
Why is a dryer not spinning?
Whether the dryer heats with gas or electricity, the drum normally turns because an electric motor drives it. On many dryers, a belt transfers that motion from a small motor pulley to the large drum pulley. Some newer dryers use a direct-drive motor instead, so there may be no belt to inspect. The heating system and the drive system are separate; a dryer can make heat without turning the drum, although normal operation should do both.
Common reasons include an overloaded drum, a door that does not latch, a paused or interrupted cycle, a broken or loose belt, a seized idler pulley, worn drum rollers, and motor or control problems. A drum that stays still while the motor hums points toward the belt or pulley system. A drum that turns but leaves clothes packed against the wall points toward rollers, glides, or broken baffles. Use those differences to narrow the problem before buying a part.
Listen for the motor, note any squeal or scraping, and check whether the drum moves by hand when the dryer is off. Stop using the dryer if you smell burning insulation, see sparks, hear loud metal grinding, or find belt pieces inside the drum. Those signs call for a repair rather than repeated test cycles.
Before you start
Unplug the dryer before you open any panel, clean near moving parts, or handle a belt. Pull the plug rather than relying on the control panel. If the dryer is hardwired, switch off its breaker instead. Let the drum, belt, and nearby parts cool before touching them. Never run the dryer with a service panel removed or with a door switch bypassed.
For a gas dryer, the drive train is still electric, but the burner, gas valve, and gas line are separate from the spinning problem. Do not take apart, test, or adjust any gas component. If you smell gas, leave the area and contact your gas utility or emergency service from a safe place. If the outlet is hot, the plug is damaged, or the breaker trips, stop and have the electrical supply checked.
Have the dryer manual, the model information from its door or rear label, a flashlight, and a screwdriver ready. Keep a small load of laundry handy for testing. A towel or tray can catch lint and small debris. Use only replacement parts identified for your dryer model, and do not use a belt by appearance alone; belt routing and pulley positions vary.
Do not probe terminals, bridge switches, or bypass a thermal fuse. If a repair requires opening the control area, disconnecting wiring, or testing the motor electrically, call a qualified appliance technician.
Step 1 Reduce an overloaded drum and restart the cycle
An overpacked drum can prevent the motor from starting or cause it to stop and restart. Dividing the laundry into smaller, loose loads lets the drum turn freely and the clothes tumble instead of remaining pressed against one side.
- Empty the drum and remove towels, blankets, and other heavy items that may have packed around the baffles.
- Make one small, loose load. Do not push clothing into a drum that will not turn freely.
- Close the door fully and make sure the latch catches.
- Press Start or Resume if the display shows a paused cycle.
- Choose an ordinary timed cycle. If the dryer has a no-heat test mode and the manual says it still turns the drum, you may use that mode for this check.
- Give the drum a moment to reach speed. If it stays still, stop the cycle instead of leaving it running.
How to tell: The drum rotates and the clothes lift and fall instead of remaining packed against the wall. If it still does not move, continue with the checks below.
Step 2 Check the door latch and cycle controls
The door must close so the control system can recognize that it is safe to start. Lint around the latch, a misaligned catch, or a damaged latch piece can keep the drum from starting. The dryer may also remain paused after a door is opened.
- Pull the plug and leave the door open.
- Wipe lint and crumbs from the visible latch area with a dry cloth. Keep cleaner and moisture out of the control area.
- Check that the door closes fully and that the latch hole lines up with the door catch.
- If the catch or latch is visibly broken, replace it according to the manual, but stop if access requires opening the control housing.
- Reconnect the dryer, close the door, and start a normal cycle. Do not hold a button or tape a switch closed.
- If the dryer starts but the drum will not move, move on to the drive checks. If there is no response at all, arrange service rather than bypassing the interlock.
How to tell: The latch clicks into place, the controls accept the start command, and the drum begins moving. If the controls stay inactive, the latch or an internal control problem needs further diagnosis.
Step 3 Clean the lint screen and confirm the dryer can move air
A clogged lint screen can restrict airflow, contribute to overheating, and interfere with normal drying. It does not usually stop the drum by itself, but a restricted exhaust should be corrected before continued operation. This check protects the dryer while you troubleshoot the drive.
- Unplug the dryer and pull out the lint screen.
- Remove the screen’s lint with your hands. Clean it with warm, soapy water only if the manual allows; let it dry completely before reinstalling it.
- Check the visible dryer exhaust opening. If it is accessible without moving the dryer, remove loose lint with a vent-cleaning tool designed for dryers.
- Do not push a sharp object into the duct, coat the duct with cleaner, or use a combustible rag. Keep hands and tools inside the cleaning tool.
- Reinstall the screen and reconnect the dryer. Start a normal cycle and confirm air moves at the exhaust outlet.
- If airflow is weak or you cannot safely reach the vent, stop and call a technician.
How to tell: The lint screen is clean, dry, and seated correctly, and air moves through the outlet. If airflow is normal but the drum still does not turn, the problem is more likely in the drive system.
Step 4 Inspect the drive belt for breaks and slipping
On a belt-driven dryer, a broken belt can leave the drum stationary while the motor still hums. A loose, burned, cracked, or badly frayed belt can also slip instead of turning the drum. Belt pieces may break loose and collect inside the drum.
If your dryer has a drive belt
- Disconnect power and remove the lint and any loose items from the drum.
- Find the service-access instructions in the manual. Remove only panels that the manual says a homeowner may access without disconnecting wiring.
- Stop if access requires lifting the drum, removing the motor, or disconnecting wiring.
- Locate the drive belt and pulleys. Check for a clean break, cracks, burned spots, deep fraying, or a belt that no longer sits squarely on the pulley.
- If the belt is broken or damaged, fit the exact replacement listed for the dryer model and route it exactly as the old belt was routed.
- Never pull the belt tight by hand, glue it, or install a belt that is not the specified shape and size.
- Reinstall every access panel before operating the dryer. If the motor still hums without drum movement, move to the idler check.
If your dryer does not have a belt
A direct-drive dryer has no drive belt. Its motor turns the drum without one. If that drum stays still, continue with the motor and control checks in Step 7.
How to tell: The drum rotates at a steady speed with no slipping sound and no belt fragments left in the drum.
Step 5 Check belt tension and the idler pulley
The idler pulley guides the belt, while a spring tensioner keeps it tight on some models. A seized pulley or damaged tensioner can allow the belt to slip, so replacing a visibly broken belt may not solve the problem by itself.
- Unplug the dryer and locate the idler pulley or belt tensioner shown in your manual.
- Turn the pulley by hand if it is accessible. It should rotate smoothly without rough spots or binding.
- Check the belt for a dull, rubbed surface or repeated slipping marks. These can mean the idler is not holding tension.
- On a spring-loaded tensioner, check that the pulley sits squarely and that the spring is seated as shown in the manual.
- Replace a seized or badly worn idler or tensioner only if the manual describes a user-serviceable replacement.
- If replacement requires removing the motor, lifting the drum, or unplugging wiring, stop and call a technician.
- Do not bend the belt, remove a spring, or tighten the belt beyond the manual’s routing.
- Restore all panels, then test a small load. Listen for a squeal or a repeating slap as the drum reaches speed.
How to tell: The belt stays seated on the pulleys and turns the drum without squealing, slapping, or visible slipping.
Step 6 Free stuck drum rollers and replace worn glides
Rollers support the drum on many top-load dryers, while glides support the lower edge of many front-load drums. Lint-packed or worn supports can make the drum stick, turn slowly, or rotate without tumbling the clothes. Broken baffles can cause the same poor tumbling even when the drum spins.
Top-load dryer
Rollers are often below the drum. Replace one at a time if the manual allows access. Do not lift the drum if doing so would pull on a wiring connector.
Front-load dryer
Glides at the lower front edge may catch lint or wear thin. Some models place support rollers at the rear, where replacement requires a technician.
- Empty the dryer, unplug it, and allow the drum to cool.
- Turn the drum by hand in both directions. If it will not move, do not force it.
- Use a flashlight to inspect accessible rollers, glides, and the lower edge of the drum for packed lint, flat spots, grooves, rust, or damage.
- Remove accessible lint buildup using the method in the manual. Do not coat the belt, rollers, or glides with grease or lubricant unless the manual specifically calls for it.
- Replace a roller or glide that the manual identifies as user-serviceable, using the matching part.
- Do not lift the drum, disconnect wiring, or remove the motor to reach a roller. If the repair is not accessible, arrange service.
- Turn the drum by hand again. It should move smoothly, without a hard stop or scraping.
- Reconnect the dryer and run a small normal load to confirm that clothes lift and tumble.
How to tell: The drum turns smoothly by hand and rotates normally during the cycle. The clothes should lift and fall rather than staying packed against the drum wall.
Step 7 Determine whether the motor or control system is failing
If the door, load, and belt are working, the remaining possibilities include the motor, its start components, or the control circuit. Listen for a hum, silence, repeated starting, or grinding. Those sounds narrow the fault before any parts are replaced.
- Reconnect the dryer, close the door, and start a normal cycle from a safe position.
- Listen for the motor. A hum with no drum turn narrows the fault to the belt or pulley system; silence narrows it to power, controls, or the motor.
- If the drum bangs, the motor grinds, or the dryer repeatedly starts and stops, stop the cycle and unplug it.
- Check the breaker and outlet before another test if the dryer gave no sign of life. If other appliances on that circuit also have no power, have an electrician check it.
- If power is present but the display or controls do not respond, have an appliance technician inspect the control system.
- Do not probe terminals, bridge a switch, test continuity on a live dryer, or replace an internal fuse by guesswork.
- If the belt and pulleys are sound but the motor hums without turning, stop. A seized motor, failed start component, or motor wiring fault needs professional testing and repair.
- For a beltless direct-drive dryer, no motor sound after a successful start command points to motor or control trouble, not belt wear.
How to tell: The motor starts and the drum rotates. If the motor remains silent or only hums, stop testing and arrange professional diagnosis.
Step 8 Complete the repair and confirm a steady tumble
A correct replacement can fail again if the belt is routed incorrectly, a pulley is damaged, or the original cause was not corrected. Finish the repair, restore every guard, and confirm the drum behaves normally before returning the dryer to regular use.
- Use the exact replacement part and follow the manual’s removal and installation sequence.
- Fit the belt flat on its pulleys, confirm that it is not twisted, and restore the belt’s original routing.
- Secure pulleys and guards as specified, but stop if a pulley will not turn or its hardware is damaged.
- Replace all access panels before testing. Never operate the dryer with the drive exposed.
- Run a normal timed cycle with a small load and watch the drum from a safe distance.
- Listen for steady rotation. Squealing, slapping, or a smell of hot rubber means stop the dryer, unplug it, and correct the fault.
- After the cycle, check the lint screen for rubber fibers or belt fragments. If they appear, do not run the dryer again until the belt is repaired.
How to tell: The drum starts promptly, reaches a steady speed, and tumbles a small load without slipping, banging, or unusual noises.
Symptom checker
| What you notice | Likely cause | Fix (step number) |
|---|---|---|
| The drum stays still and the motor is silent | Paused cycle, open door, failed controls, or motor trouble | Steps 1, 2, and 7 |
| The motor hums but the drum stays still | Broken belt, slipped belt, or seized idler pulley | Steps 4 and 5 |
| The drum starts slowly or stops under a large load | Overload, packed baffles, or restricted rollers | Steps 1 and 6 |
| The drum turns but the clothes remain packed | Worn rollers, clogged glides, or broken baffles | Step 6 |
| A squeal or repeated slap occurs during rotation | Slipping belt, damaged pulley, or worn roller | Steps 4 through 6 |
| There is a burning smell, smoke, or sparks | Damaged belt, seized motor, or electrical fault | Stop and arrange service through Step 7 |
| The dryer starts and then pauses repeatedly | Overload, control interruption, or overheating | Steps 1, 2, and 3 |
| The drum spins but the dryer does not heat | Restricted airflow or a heating-system fault | Step 3; use a professional for burner service |
| The door will not close completely | Obstructed latch, misaligned catch, or broken latch piece | Step 2 |
Mistakes that make it worse
- Continuing to run the dryer after finding broken belt pieces, a burning smell, or smoke.
- Forcing a seized drum or pulley instead of finding the lint, roller, or bearing obstruction.
- Spraying grease or lubricant on a belt, pulley, or roller unless the manual specifically calls for it.
- Stretching, gluing, or trimming the belt, or installing a belt from a different dryer.
- Bypassing a door switch, thermal fuse, or control to force the motor to run.
- Ignoring repeated squealing or slipping sounds instead of stopping the dryer and inspecting the drive.
When to call a professional
- You need internal wiring, control-board, thermal-fuse, or motor electrical testing.
- The motor hums, repeatedly buzzes, grinds, or does not turn even though the belt and pulleys appear sound.
- Replacing the belt, idler, or rollers requires lifting the drum, removing the motor, or disconnecting wiring.
- The outlet is hot, the plug is damaged, the breaker trips, or other appliances on the same circuit lose power.
- You smell burning insulation, see smoke, or notice scorch marks around the motor or control area.
- Any work involves a gas burner, gas valve, gas line, or suspected gas leak. Use a licensed gas professional; do not work on those components yourself.
How to keep it from happening again
- Clean the lint screen at the interval specified in the dryer manual and inspect the screen for belt fibers.
- Use loads that fit loosely enough for the drum to turn and the clothes to tumble.
- Keep heavy items from wrapping around rollers or filling the space around the drum baffles.
- Have the vent checked regularly and remove exterior lint buildup as directed by the manual.
- Stop the dryer when you hear new squealing, scraping, or slipping, and inspect the belt and idler before using it again.
Frequently asked questions
Why is my dryer not spinning but still heating?
The heating system and drum drive are separate, so heat alone does not confirm that the drum should be turning. A broken or slipped belt can leave the motor running while the drum stays still. Stop the cycle, unplug the dryer, and inspect the accessible drive parts.
Is a broken dryer belt dangerous to run?
A broken belt can leave loose fragments in the drum, and an exposed belt or pulley can snag fabric or damage moving parts. A burning smell also signals a possible overheating problem. Unplug the dryer and do not run it until the belt and pulley system have been checked and repaired.
How can I tell if the belt or the motor is the problem?
A motor hum with a stationary drum usually points to the belt or idler system. Silence after a valid start command points to the power, controls, or motor. Electrical testing of the motor and internal wiring belongs with a qualified technician.
Can I use the dryer with a broken belt?
Do not run the dryer with a broken belt. It may fail to tumble, shed belt pieces into the drum, or allow further drive-system damage. Disconnect power and have the belt, tensioner, and pulleys inspected before testing again.
Why does the drum turn but the clothes do not tumble?
The load may be too large or packed tightly around the baffles. Worn rollers, lint-covered glides, or broken baffles can also prevent proper lifting and falling. Reduce the load and complete the roller and glide checks in Step 6.
Do gas dryers need different belt and motor repairs than electric dryers?
Their mechanical drive systems are handled in much the same way because the drum is driven by an electric motor in either setup. Heating-system work is different. Any burner, gas valve, gas line, or suspected gas leak requires a licensed gas professional.
What this guide is based on
- Dryer support geappliances.com
Revision history
- Updated and re-checked against sources.
- First published.
Did this fix it?
Thanks. Glad it's sorted.
Sorry it's still not right. Recheck the symptom checker above, or tell us what you're seeing.