On this page
Quick answer
Most slow drains are clogged by hair, soap residue, food particles, or a buildup in the drain trap. Start by checking the strainer or stopper, then try a plunger or drain snake. For showers, remove the cover and clear the hair from the drain. Avoid pouring harsh chemical drain cleaner.
At a glance
- Time
- 15–45 min
- Difficulty
- Easy
- You'll need
- Bucket, towels, gloves, plunger, drain snake, and basic hand tools
- Cost
- Free for most fixes; replacement parts if needed
- Works on
- Kitchen and bathroom sinks, showers, and bathtubs
- Not covered
- Main sewer clogs, hidden pipe damage, appliance repairs, and gas work
Why does a drain clog?
Water from a sink or shower travels through a drain pipe by gravity. A sink usually has a curved section called a P-trap under the basin. This curve holds enough water to block sewer gases from entering the room. A shower also has a trap, but it is usually hidden beneath the floor or inside the wall.
Hair, soap, food particles, and grease collect at different points in the system. A sink strainer catches larger pieces, while smaller debris can settle in the trap or stick to soap residue farther down the pipe. That partial buildup narrows the opening, so water drains slowly and may gurgle as air moves through the remaining gap.
A clog near the opening often clears with basic cleanup. If the same debris keeps returning after you clean the trap, the blockage may be deeper in the branch pipe or in a shared line. Slow drains in several fixtures point toward a shared-line problem, while a single slow sink or shower more often has a local blockage.
Before you start
Put a bucket, old towels, rubber gloves, and a flashlight within reach. A plunger, a screwdriver that fits your drain hardware, adjustable pliers, and a hand drain snake cover most household clogs. Keep removed washers, nuts, stoppers, and covers together so you can reinstall them in the correct order.
If the sink has a garbage disposal, unplug it or switch off its circuit at the breaker before reaching into the drain or placing tools inside it. Do not open the disposal or work on internal wiring. Do not work on gas lines, gas valves, or gas burners; if gas equipment is involved, call a licensed professional.
Before you loosen a trap or supply connection, turn off the faucet. If you need to shut off the water supply, close the shutoff valve before removing any fitting, and place the bucket directly below the joint. You will catch water when you disconnect the trap, so remove items from the cabinet first and protect the surface with towels.
Avoid chemical drain cleaner as a first step. Chemical cleaners can splash when you later plunge or snake the drain, and repeated use can make the opening harder to work on safely. Use a plunger, a cleaned trap, and a mechanical snake first. Stop if you smell gas, see damaged wiring, or notice a leak you cannot control.
Step 1 Remove and clean the drain strainer
Why this works: A strainer or stopper sits where much of the hair, food, and debris collects. Removing and rinsing it can clear a partial blockage without pushing the debris farther into the pipe.
- Place a towel over the drain opening, then remove the stopper or strainer. Lift it straight out, twist it free, or release the retaining nut, depending on the design.
- Pull off any hair or buildup caught around the stopper. If it is a pop-up stopper, check that the lift rod and hinge are not holding it partly closed.
- Remove the strainer if it is separate. Rinse it under warm water and clear the holes with a soft brush.
- Check the drain opening for food, hair, soap, or objects. Use a gloved hand or a blunt plastic tool rather than a sharp knife.
- Check that the stopper is not cracked, loose, or sitting too low. If it is damaged, replace it with one that matches the opening and the existing hardware.
For a shower drain
Lift out a removable hair screen or cover. If the cover is held by screws, remove only the screws intended for it and keep them in order. Do not pry a fixed cover or force a cover that will not lift. If the design is unclear, ask a plumber for help.
How to tell it worked: Run water and watch the opening. If the drain takes water faster and debris does not return, move on to preventive flushing. If the flow stays slow, continue with plunging.
Step 2 Plunge the drain
Why this works: A plunger creates pressure changes that can loosen a blockage and move it toward the opening. It works best when the cup forms a tight seal over the drain and enough water is present to push the clog.
- Remove the stopper or strainer if it prevents the plunger from sealing. Do not run a garbage disposal while the plunger is in the drain.
- Fill the basin with enough water to cover the plunger cup. A small amount of mild dish soap can help the cup seal.
- Center the cup over the drain opening. Push down firmly several times without lifting the cup, then lift it slightly to release pressure and repeat.
- After several rounds, lift the cup and check the flow. If water is moving, run more water to flush the loosened material.
- If the blockage does not move, remove the plunger and move to another method instead of pounding harder.
For a shower or bathtub
For a shower, cover the drain with the plunger and add enough water to cover the cup. Keep the cup flat against the drain floor and plunge straight down. For a bathtub, plug the drain, add a shallow layer of water, and plunge over the drain opening.
For a kitchen sink with a disposal
Unplug the disposal or switch off its breaker first. Never put your hand into the disposal chamber, and never plunge while the disposal is running.
How to tell it worked: Water should begin leaving the basin faster, and gurgling should stop. If several rounds of plunging change nothing, clean the trap or use a drain snake.
Step 3 Flush the drain with hot water and dish soap
Why this works: Dish soap breaks up greasy residue, and hot tap water can carry loosened material toward the trap. This method works best on soap and grease buildup, not on a solid object or a tightly packed hair clog.
- Remove any solid debris from the opening and put the strainer or stopper back in place.
- Pour a small amount of mild dish soap into the drain. Let it sit briefly while you prepare to run the water.
- Run hot tap water steadily, starting with a moderate stream so the drain does not overflow.
- Stop if the drain overflows, the water rises, or you notice a leak.
- For a shower, remove the hair screen before running water so loose residue can leave instead of settling again.
- After the water drains, rinse the strainer and remove any residue that remains around the opening.
Do not pour boiling water into the drain. It can crack porcelain fixtures and can damage a garbage disposal. Hot tap water is safer for routine flushing.
How to tell it worked: The drain should empty faster, with less standing water and fewer soap or grease deposits. If nothing changes, clean the trap or use a drain snake.
Step 4 Clean the sink P-trap
Why this works: The P-trap is designed to catch some debris before it reaches the sewer. Cleaning it removes material that a strainer and plunger cannot reach.
- Empty the cabinet and place a bucket under the trap. Put down towels, turn off the faucet, and move the drain hose aside if needed.
- If you must disconnect a supply line, close its shutoff valve before loosening the connection. Unplug the garbage disposal or switch off its breaker.
- Loosen the slip-joint nut below the sink. Support the trap with one hand so it does not pull on the tailpiece.
- Lower the trap and expect water to drain into the bucket. Remove the U-shaped section or the entire assembly, depending on the design.
- Clean trapped debris from the bend and check the slip joints. Do not push a brush deep into the pipe.
- Inspect the rubber washers and slip-joint seals. Replace a cracked washer or a damaged section with a matching part.
- Reassemble the trap by hand, tightening the slip joints only enough to seal. Open the shutoff valve slowly, then test the faucet and joint for leaks.
For an accordion-style trap
Loosen the nuts, remove the flexible section, and clean the ridges where grease and hair collect. Reconnect it fully so the section cannot sag, pull apart, or leak.
How to tell it worked: The sink should drain normally, and the joint should stay dry. If water appears below the sink, turn off the faucet, close the supply valve if needed, and reseat the leaking joint before using the sink again.
Step 5 Clear hair from a shower drain
Why this works: Hair is light enough to move but snags on rough plastic and metal edges. Soap and body oils bind the hair into mats, and those mats catch on the drain opening.
- Remove bottles and other items from the shower floor. Place a towel near the drain to catch water and small debris.
- Lift out the hair screen or removable cover. If the design uses screws, use the correct screwdriver and keep the screws together.
- Pull visible hair into a clump with a gloved hand or a plastic drain-hair tool. Do not use a sharp knife or stiff wire.
- Rinse the screen under warm water and clear its openings with a soft brush. Check the underside and the edges of the cover.
- Reinstall the screen or cover so it sits flat and cannot wobble. A loose cover can let hair slip underneath and into the opening.
- Run the shower and watch the drain. If water still pools, try the plunger method in Step 2 before using a snake.
- Clean the screen again after each buildup and check the drain opening for a mat that has formed below it.
How to tell it worked: Water should flow around the drain instead of pooling over it. If the pool disappears only when you remove the cover, the screen or cover may need more thorough cleaning.
Step 6 Work a drain snake through the pipe
Why this works: A drain snake can reach a blockage beyond the stopper and trap. Turning the handle at the point of resistance can break the clog apart or pull it back toward the opening.
Unplug a garbage disposal or switch off its breaker before inserting a snake. Do not push a snake through the disposal unless the unit’s instructions specifically allow it. Wear gloves and keep the cable away from sharp metal edges.
- Remove the stopper or strainer. For a sink with a disposal, keep the tool out of the disposal chamber and use the drain opening only.
- Feed the snake tip into the drain slowly. Stop if the tip meets a hard stop, a sharp edge, or the trap connection.
- Advance more cable while turning the handle when you feel resistance. Keep the cable under control and do not force it.
- When the snake reaches the clog, rotate the handle to break up or hook the material. Continue withdrawing slowly and watch the drain opening.
- Pull the cable out gradually, stopping if the sink begins to drain so you do not splash trapped water onto the counter.
- Flush the drain with hot tap water and rinse the strainer. Clean the snake before storing it.
- Reinstall the stopper or shower cover and test the drain again.
If the snake stops immediately
A hard stop can mean the snake has reached the trap, a damaged fitting, or another obstruction. Do not force it past that point. Check whether a smaller drain cable can pass, but do not use a stiff wire, knife, or improvised hook because these can scratch the pipe or break off inside it.
How to tell it worked: Water should drain freely, and no debris should reappear after a full flush. If the blockage remains, the obstruction may be farther down the line or inside the shared drain system.
Symptom checker
| What you notice | Likely cause | Fix (step number) |
|---|---|---|
| The drain is slow and debris is visible at the opening | Strainer or stopper blockage | Step 1 |
| A kitchen sink drains slowly and the water looks greasy | Soap or grease buildup | Steps 3 and 4 |
| The drain gurgles after the basin empties | A partial blockage is allowing air through | Steps 1 and 2 |
| Shower water pools and hair gathers near the drain | Hair and soap caught on the screen | Steps 1 and 5 |
| Water rises or returns after you plunge | Obstruction in the trap or a nearby pipe | Steps 4 and 6 |
| The sink backs up when the faucet runs | A local blockage farther down the line | Stop running water; Steps 1, 3, and 6 |
| The stopper stays low or does not open fully | A damaged or misaligned stopper | Step 1 |
| Water appears under the sink after removing the trap | A loose slip joint or failed washer | Step 4 |
Mistakes that make it worse
- Pouring boiling water into the drain, which can crack porcelain fixtures or damage a garbage disposal.
- Using chemical drain cleaner and then plunging or snaking, which can cause the stored chemical to splash out.
- Reaching into a disposal or running it with a tool in the chamber. Unplug it or switch off its breaker first.
- Forcing a snake past resistance or using a stiff wire, which can scratch the pipe, damage a fitting, or leave part of the tool inside.
- Overtightening slip-joint nuts or forcing incompatible replacement parts, which can strip threads, crack fittings, or cause a leak.
- Ignoring backups in several drains and continuing to run water, which can turn a local problem into a sewage overflow.
When to call a professional
- Several drains are slow, gurgling, or backing up at the same time. A shared branch or main sewer blockage may be responsible.
- Sewage or dirty water backs up into a sink, shower, or floor drain. Stop running water and arrange a professional inspection.
- The drain remains blocked after you clean the strainer, trap, and pipe. The obstruction may be beyond the reach of household tools.
- The trap nuts are seized, heavily corroded, or break when you loosen them. Do not force them.
- A trap, pipe, or fitting leaks after you disconnect it, or you notice a leak inside a wall or floor.
- A garbage disposal needs to be opened, or you suspect damaged internal wiring. Unplug it or switch off the breaker, then call a qualified technician or licensed electrician.
How to keep it from happening again
- Clean the sink strainer and shower hair screen regularly so trapped debris does not build up.
- Use a shower hair catcher and empty it before the hair forms a mat.
- Keep food scraps out of the sink and pour cooking grease into a container instead of the drain.
- Flush kitchen drains with hot tap water and a small amount of mild dish soap after food preparation.
- Check under the sink for drips, corrosion, or a slow trap joint before a small leak becomes a larger one.
- Avoid relying on harsh chemical drain cleaner for routine cleaning; remove debris and clean the trap instead.
Frequently asked questions
What is the fastest way to unclog a drain?
Remove and clean the strainer or stopper first, because debris there is easy to reach. If the drain is still slow, use a plunger with a tight seal. Move to the trap or a drain snake if plunging does not help.
Does baking soda and vinegar really unclog a drain?
They may loosen light soap or grease residue, but they usually do not remove hair, food, or a solid obstruction. Clean the strainer, plunger, and trap first. Never mix chemical drain cleaners, including with household cleaners.
Why does my shower drain clog so often?
Hair catches around the drain screen and binds to soap and oils. Clean the screen and cover regularly and use a hair catcher. If hair has built up below the opening, try the plunger and shower steps in this guide or call a plumber.
Is boiling water safe to pour down a drain?
Use hot tap water instead. Boiling water can crack porcelain fixtures and can damage some garbage disposals. Dish soap plus hot tap water is safer for routine buildup.
Why is my sink still slow after I remove the stopper?
The clog may be in the P-trap or farther down the pipe. Clean the trap next, then use a drain snake. If the sink backs up or the problem returns after those steps, call a plumber.
Should I call a plumber if more than one drain is clogged?
Yes. If several sinks or a shower overflow, the blockage may be in a shared branch or main sewer line. Stop using harsh chemical cleaner and arrange a professional inspection, especially if sewage is backing up.
Revision history
- Updated and re-checked against sources.
- First published.
Did this fix it?
Thanks. Glad it's sorted.
Sorry it's still not right. Recheck the symptom checker above, or tell us what you're seeing.