On this page
Quick answer
A blocked toilet usually comes from a paper buildup, a stuck flush component, a full tank, or a clog deeper in the drain. First, stop flushing and check for overflow. Remove the tank if it keeps filling, then try a plunger with enough water to cover the cup. If that fails, use a toilet auger without forcing it.
At a glance
- Time
- 15–45 min
- Difficulty
- Moderate
- You'll need
- Plunger, toilet auger, bucket, gloves
- Cost
- Free for basic methods; a tool or part if one is needed
- Works on
- Residential toilets with blockages in or just below the bowl
- Not covered
- Main sewer clogs, leaks, cracked toilets, or complex tank repairs
Why does a toilet become clogged?
A household toilet uses water stored in a tank to create a fast-moving flush. The flush pushes waste into a curved section of the drain called the trap, then into the larger drain line. Water left in the trap creates a seal between the bathroom and the sewer. A clog can form in the bowl, inside the trap, just below the toilet at the floor outlet, or farther down in the home’s drain line.
Most toilet clogs come from material that does not disperse and move away: excess toilet paper, wet wipes, hygiene products, dental floss, or a small object. Several large paper products flushed at once can form a dense wad even when each item would normally pass. Hard objects and grease or soap buildup can also lodge in the narrow trap. In some homes, a recurring problem comes from a blockage farther down the shared drain line rather than from anything flushed in this toilet.
Tell the symptoms apart before choosing a fix. If the bowl drains slowly, the blockage is probably soft and near the toilet. If it does not drain at all, the obstruction is firmer or deeper. If the bowl empties but the tank keeps running or refilling, the waste may be clear while a flapper, fill valve, or float needs attention. If several drains gurgle or back up, the toilet is only one sign of a larger drain problem.
Before you start
Stop flushing as soon as the bowl begins to rise. If water is approaching the rim, turn the toilet’s shutoff valve clockwise until it stops. Put towels around the base, keep children and pets away, and do not add more water to an overflowing toilet.
Have a bucket, old towels, disposable gloves, a flashlight, and a plunger on hand if possible. A toilet auger can reach a blockage that a plunger cannot move. Wear gloves and wash your hands and tools after the job. If the floor is wet, keep electrical appliances and power cords away from it.
Before opening the tank, disconnecting the supply line, or removing the toilet, close the toilet’s shutoff valve. Before setting up a powered wet/dry vacuum, unplug it and keep the plug and power connection dry. No gas line, burner, or gas valve is part of this task. Do not work on gas lines or appliance wiring; if a gas-fired water heater or an electrical device seems to be involved, call a licensed professional.
- Do not mix bleach, acids, ammonia, or drain cleaners.
- Do not use boiling water on a toilet bowl.
- Do not push an object or tool deeper without knowing what it may hit.
- Use hot tap water only, because sudden temperature changes can crack porcelain.
Step 1 Stop the overflow and identify the blockage
Why this fix works: Every extra flush adds water that the blocked toilet cannot remove. Stopping the water and lowering the bowl level prevents another spill and lets you see where the problem sits.
- Stop using the flush handle and warn others not to flush.
- Turn the shutoff valve on the wall or floor behind or beside the toilet clockwise until the water flow stops.
- Place towels around the toilet base and move rugs, paper, and other items out of the way.
- If the bowl is close to overflowing, use a disposable cup or small container to remove excess water into a bucket. Do not pour it into another toilet.
- Use a flashlight and look from above. Check for a visible wad, object, or foreign material near the drain opening.
- Note whether the bowl drains a little, stays at the same level, or rises. Also note whether the tank is still filling or running.
- Do not flush again until you have tried a clearing method.
How to tell whether it worked: You have controlled the immediate overflow if the water stops rising and stays below the rim. The blockage itself is cleared when one controlled flush moves the water normally without sending the bowl back up.
Step 2 Use a plunger to create pressure under the clog
Why this fix works: A plunger changes the pressure inside the bowl. Repeated strokes can move a soft blockage, create a rush of water, or pull trapped material back toward the drain.
Choose the plunger and water level
A flange plunger has a rubber rim shaped to seal around the toilet drain. A cup plunger can handle a minor blockage, but it may not seal as well. The water in the bowl should cover the rubber cup without leaving the bowl close to overflowing.
- Put on gloves and place a towel over the floor around the toilet.
- If there is too little water in the bowl, add enough hot tap water to cover the plunger cup. If there is too much, remove some into a bucket.
- Position the plunger directly over the drain opening. Drain the bowl enough to create a seal, but do not force the cup into the opening.
- Push down slowly several times to release trapped air.
- Then plunge with firm, even strokes while keeping the cup sealed over the drain.
- Do not lift the cup far enough to break the seal between strokes, and do not move it sideways against the bowl.
- After several cycles, check whether the water level drops or the bowl makes a gurgling movement.
- If the level drops, flush once. If nothing changes, move to a toilet auger instead of continuing forcefully.
How to tell whether it worked: The bowl should drain after a plunge or after one controlled flush. If water remains at the same high level, stays near the rim, or rises again, the obstruction is not gone.
Step 3 Work the obstruction with a toilet auger
Why this fix works: A toilet auger has a cable that can pass through the bowl and trap. Its coiled end can snag a blockage or push it farther into the drain so the next flush can carry it away.
- Stop flushing and turn the toilet’s shutoff valve clockwise if water is still entering the bowl.
- Place a bucket under the bowl area and spread towels around the base.
- Feed the auger cable slowly into the drain opening while turning the handle in the direction marked by the manufacturer.
- Stop advancing the cable when you feel resistance. Do not push hard or crank the handle against a sudden stop.
- Keep the handle turning gently while you pull the cable upward. The coiled end may catch the obstruction and bring it toward the opening.
- If the cable will not pass, withdraw it slowly and inspect the coil. A large or hard object may require a professional.
- Clean the cable and return it to its holder before checking the toilet.
Keep the cable from scraping the bowl’s glazed surface. If you feel the cable strike the bottom of the trap or a hard stop, stop turning and withdraw it.
How to tell whether it worked: The auger may bring waste or another object back with it. Otherwise, the blockage is cleared if the bowl drains after you flush once and the water level stays down.
Step 4 Remove a clearly visible object from the bowl
Why this fix works: If a toy, toothbrush, sponge, or another object is caught near the drain, removing it directly can clear the toilet without pushing it deeper.
- Stop flushing and put on disposable gloves.
- Lower the water level if the object is submerged and the bowl is close to overflowing.
- Use rubber-coated tongs or another safe retrieval tool to grasp only an object that you can clearly see.
- Pull the object straight out slowly and place it in a trash container.
- Do not use a wire coat hanger, screwdriver, or narrow tool that can scratch the bowl or damage the trap.
- If you cannot see and grasp the object, do not fish blindly. Use the toilet auger instead.
- Flush once only after the visible obstruction has been removed.
How to tell whether it worked: The object should be out of the bowl, and the next flush should move normally without the bowl refilling to a high level.
Step 5 Flush a soft buildup with hot, soapy tap water
Why this fix works: Hot tap water can loosen a soft mix of paper and soap, while dish soap helps wet the material and keep it from clinging as tightly to the trap.
- Do not use a chemical drain cleaner, and do not add boiling water.
- Stop flushing while the bowl contains standing water.
- Add several squirts of ordinary dish soap to the bowl.
- Pour in hot tap water slowly until the bowl reaches a normal operating level without approaching the rim.
- Let the mixture sit for several minutes while you continue other safe steps.
- Place the plunger over the drain and use several firm strokes.
- If the bowl still does not drain, use a toilet auger rather than adding more water or chemicals.
Boiling water can create a sudden temperature change that cracks porcelain. Never combine dish soap with bleach, acid, ammonia, or a drain cleaner.
How to tell whether it worked: The bowl should drain after plunging or after one controlled flush. A strong chemical odor, fumes, or a rising bowl means you should stop adding products and ventilate the room.
Step 6 Try a wet/dry vacuum for a water-only clog
Why this fix works: A wet/dry vacuum can remove standing water and create strong suction around a light obstruction. It is less reliable than an auger and can splash dirty water, so use it only with the correct bowl attachment.
- Confirm that the vacuum is designed for wet pickup. Do not use an ordinary dry household vacuum.
- Unplug the vacuum, empty the canister, and attach the toilet bowl adapter while the plug is disconnected.
- Keep the power cord, plug, and motor away from wet floor areas.
- Lower the vacuum tip into the bowl and position it at the water surface without striking the ceramic.
- Plug in the vacuum and turn it on while keeping the attachment sealed around the bowl opening.
- Move the tip gently across the drain area so the suction can reach the blockage.
- Turn off and unplug the vacuum before lifting the attachment out of the water.
- Empty and clean the canister, then flush once only if the bowl has drained.
Skip this method if you cannot keep the electrical connection dry. If a powered tool must be connected near standing water, switch off the breaker before setup and do not handle the plug with wet hands.
How to tell whether it worked: The water level should fall and remain down after the tool is removed. If the blockage stays in place, use an auger or call a plumber rather than increasing the suction.
Step 7 Repair a tank that runs or fills too high
Why this fix works: A flapper that cannot seal, a stuck fill valve, or a float set too high can send water into the bowl continuously. That extra water can make a normal blockage overflow or appear to make the toilet more clogged.
- Turn the toilet’s shutoff valve clockwise until the water supply stops.
- Lift the tank lid and look for a flapper, fill valve, float, chain, or debris that is holding the mechanism open.
- Use a disposable container to remove excess tank water so you can see the parts clearly.
- Clean a dirty flapper gently with mild soap and water. Make sure it can seat squarely over the flush valve opening.
- Check that the chain is connected and is not caught under the flapper or another part.
- Move the float up and down by hand. It should rise and fall freely without touching the tank wall.
- Adjust the float only to the fill mark provided on the tank or by the toilet manufacturer’s instructions.
- Open the shutoff valve slowly and watch the tank fill. Stop and close the valve if the water approaches the overflow tube.
- If the tank still runs after cleaning and adjustment, replace the failed component with a compatible part or call a plumber.
After the tank fills correctly and the bowl is clear, flush once and watch the complete cycle. The tank should refill to its marked level and stop without continued running.
How to tell whether it worked: The tank should stop filling at the correct level, and water should not continue entering the bowl after the flush cycle ends. A bowl that still remains full has a separate blockage.
Step 8 Remove the toilet to clear the outlet
Why this fix works: If the obstruction sits below the trap or inside the toilet’s floor outlet, removing the toilet gives a toilet auger direct access. This is a last-resort job because porcelain can crack and the floor seal can be damaged.
- Stop flushing and turn the toilet’s shutoff valve clockwise before touching the supply line.
- Place a bucket under the supply connection, disconnect the toilet’s water supply, and cap or plug the line if possible.
- Empty the tank and bowl into the bucket as far as the blockage allows.
- Remove the tank according to the toilet’s installation instructions and set it on a protected surface.
- Remove the nuts securing the toilet to the floor and rock the toilet gently to loosen it from the flange.
- Lift the toilet straight up with another person if necessary. Do not twist hard or pull on the bowl.
- Inspect the floor outlet. Feed the toilet auger into the opening and work it slowly, using the same resistance rule as before.
- Stop if the auger meets a hard obstruction that will not move or if other drains begin gurgling.
- If the toilet and flange are intact, reinstall the toilet with a new compatible seal according to the manufacturer’s instructions.
- Restore the water supply slowly and test for leaks and normal drainage.
Do not remove a cracked toilet or force corroded bolts. If the floor flange is damaged, the toilet cannot be lifted safely, or the clog appears to be in the main drain, stop and call a plumber.
How to tell whether it worked: After reinstallation, the toilet should fill without leaking, and one flush should empty the bowl normally. Repeated backups suggest that the obstruction is farther down the drain line.
Symptom checker
| What you notice | Likely cause | Fix (step number) |
|---|---|---|
| Water rises to the rim and spills out | Blockage combined with an open tank valve | Step 1, then Step 3 |
| Water drains very slowly after a flush | Soft paper, grease, or soap buildup | Step 2, then Step 5 |
| The bowl does not drain at all | Firm obstruction in the trap or outlet | Step 3 |
| The bowl empties, but the tank keeps running | Flapper, float, or fill-valve problem | Step 7 |
| A toy, sponge, or other object is visible | Object lodged near the drain opening | Step 4 |
| The flush runs, but the bowl barely moves | Blockage or a failed flush-valve mechanism | Steps 2 and 3; check Step 7 |
| The tank fills and overflows while the bowl drains | Fill mechanism set too high or not shutting off | Step 7 |
| The bowl gurgles as it drains | Air in the drain line or a partial obstruction | Step 3 |
| The clog returns after every flush | Obstruction farther down the drain line | Step 3; call a professional if it returns |
Mistakes that make it worse
- Keeping the flush handle pressed or flushing repeatedly after the bowl stops draining.
- Pouring boiling water into the bowl, which can crack porcelain through thermal shock.
- Mixing bleach with vinegar, acids, ammonia, or drain cleaner and creating toxic fumes.
- Using a coat hanger, screwdriver, or other hard tool that can scratch the bowl or push an object deeper.
- Forcing a plunger or auger after it meets a hard stop, which can damage the tool or toilet.
- Using a powered vacuum near standing water without a wet-rated tool, dry hands, and a protected power connection.
When to call a professional
- Call a plumber if the blockage remains after careful plunging and one or two attempts with a toilet auger.
- Seek help if the clog returns repeatedly or if other sinks, tubs, or floor drains gurgle, slow down, or back up at the same time.
- Call for help if you cannot shut off the toilet’s water valve or if water keeps entering the bowl after the supply is closed.
- Call for help if water is leaking around the toilet base or if the porcelain, floor bolts, or floor flange appear damaged.
- Do not attempt to remove a large hard object, a toy lodged deep in the trap, or a blockage in the main drain line.
- Call a qualified professional if removing and reinstalling the toilet would require cutting corroded bolts, forcing a damaged flange, or working around unsafe electrical conditions.
How to keep it from happening again
- Flush only toilet paper and human waste; do not flush wipes, cotton swabs, floss, hygiene products, or small objects.
- Split a large load of toilet paper into several flushes instead of creating one dense wad.
- Keep the bowl and trap reasonably clean so paper, soap, and mineral residue do not build up around the drain.
- Check the flapper, fill valve, and float when the toilet runs continuously or takes too long to fill.
- Use only hot tap water for minor buildup, and never pour grease, paint, oil, or chemical drain cleaner into the toilet.
- If clogs recur even when you flush only toilet paper, arrange a drain inspection instead of repeatedly using stronger tools or products.
Frequently asked questions
How do you unclog a toilet without a plunger?
A toilet auger can reach many blockages that a plunger cannot move. For a soft buildup, try hot tap water and dish soap, and remove a clearly visible object with gloves and a safe retrieval tool. Skip chemical drain cleaners and stop if the obstruction is deep.
Does baking soda and vinegar really clear a toilet?
The fizzing reaction is brief and usually does not create enough force to remove a blockage. It may not clear the clog and can leave you wasting time while water remains in the bowl. Use a plunger or toilet auger instead.
Can I use boiling water to unclog a toilet?
No. Boiling water can crack porcelain through a sudden temperature change. Use hot tap water only, and stop if the bowl begins to rise.
Why does my toilet keep running after I flush?
A stuck or dirty flapper, a faulty fill valve, or a float set too high can keep water entering the bowl. Close the toilet's water valve, clean and check the tank components, and adjust the float only to the marked level.
Why does the water come back up after I flush?
The bowl is likely holding a blockage that prevents the flush from leaving the toilet. Stop flushing, close the shutoff valve if water is rising, and use a toilet auger. Call a plumber if the clog returns or other drains are affected.
When should I stop and call a plumber?
Stop if repeated plunges and careful auger use do not clear the toilet. Call a plumber for recurring backups, gurgling in other drains, leaks, cracked porcelain, a damaged floor flange, or a shutoff valve that will not close.
What this guide is based on
- Environmental Protection Agency epa.gov
- American Standard americanstandard-us.com
Revision history
- Updated and re-checked against sources.
- First published.
Did this fix it?
Thanks. Glad it's sorted.
Sorry it's still not right. Recheck the symptom checker above, or tell us what you're seeing.