On this page

Quick answer

The most common causes are a tripped reset, a jammed impeller, food or debris caught in the drain, or a blockage farther down the sink line. First, switch off the disposal’s breaker and check that the drain hole is clear. Then reset the unit and test it with cold water. If it hums without spinning or still will not drain, follow the steps for those symptoms.

At a glance

Time
15–45 min
Difficulty
Easy
You'll need
Bucket, tongs or a tool, flashlight, and a hex key if your model uses one
Cost
Free for most fixes; a part if one is worn
Works on
Common residential electric garbage disposals with a reset button
Not covered
Internal wiring repairs, gas work, or serious sewer-line damage

Why is your garbage disposal not draining?

Garbage disposal not working? A garbage disposal does not move food through the sink by itself. Its motor spins an impeller that pushes waste toward the drain, while water carries the waste into the household drain line.

  • If the disposal hums but does not turn, the motor may be trying to move against a jam.
  • If it runs normally but the sink will not empty, the blockage may be below the disposal or in the sink drain.
  • Common problems include a tripped reset button, a stuck flywheel, a lost or damaged hex key, food lodged around the impeller, a clogged dishwasher or sink drain connection, and a blockage in the branch drain.
  • A disposal can also seem dead after a jam overloads or activates its protective shutoff.

Knowing whether the unit is silent, humming, spinning, or running without draining helps you avoid using the wrong fix.

Never force the disposal to run if it hums, clicks, smells burned, or vibrates heavily. A stuck key or jam can damage the impeller, and continuing to run a motor against an obstruction can overheat it.

If the problem persists after the basic checks below, stop and arrange a plumber or qualified appliance repair professional.

Before you start

  • Turn off power first. Find the breaker that controls the disposal and switch it off before you reach under the sink, remove a guard, inspect the blades, or handle any electrical plug or wire. Do not rely only on the wall switch.
  • Protect the sink and floor. Place a bucket under the drain, wear gloves, and keep tools and small parts from falling into the pipe.
  • Stop the water if needed. Most disposal repairs do not require shutting off the sink’s water supply. If you must move a supply line or open a fitting, close the sink’s shutoff valve first and open the cold faucet to confirm the water is off.
  • Use the right tools. You may need a flashlight, long tongs or a disposal tool, a flat or Phillips screwdriver, pliers, a hex key, and a bucket. Do not use your fingers inside the disposal.
  • Do not open the motor housing. Internal wiring and motor repairs are not covered here. If the reset and visible jam checks do not restore operation, call a qualified professional.

Step 1 Check for an obvious sink blockage

This is the fastest way to rule out a simple plug of food, soap, or debris sitting in the sink drain. It also tells you whether the disposal needs attention at all. Because the drain may contain sharp objects, do not reach into it while the disposal could start.

  1. Switch off the breaker that powers the disposal. If you cannot identify it, test only the disposal’s wall switch by switching it off and do not handle any plug or wiring under the sink until the power is off.
  2. Remove the sink strainer, stopper, or disposal splash guard according to your sink’s instructions. If the guard is part of the disposal flange, follow the manufacturer’s removal instructions rather than prying against the motor housing.
  3. Use a flashlight to look into the drain opening. Look for food, bottle caps, packaging, utensils, or objects that could have fallen into the sink.
  4. Remove loose debris with tongs or a disposal tool. If an object is wedged below the opening, do not try to pull it out with your fingers.
  5. Pour a small amount of cold water into the drain and watch whether it disappears. If the water backs up immediately, the blockage is likely in the drain line rather than inside the disposal.
  6. Replace the strainer or guard. If the sink drains normally and the disposal spins freely, the obstruction is cleared.

How to tell it worked: Cold water should flow through the sink without pooling, and the disposal should start and stop normally when you operate its switch.

Do not use chemical drain cleaner in a garbage disposal unless the product label explicitly permits it. Some products damage plumbing seals, metal parts, or septic systems.

Step 2 Reset the garbage disposal

Many disposals have a red or other clearly marked reset button on the motor body. The reset button may have tripped after a jam or overload. Resetting it restores the electrical connection but does not remove a blockage, so test the unit carefully afterward.

  1. Switch off the disposal’s breaker and confirm that the wall switch is off before reaching under the sink.
  2. Locate the reset button on the underside of the motor housing. Do not remove the housing or touch wires near the button.
  3. Press and hold the reset button for the short period stated in the disposal’s instructions. If you do not have the manual, do not hold it for an extended time or force the button.
  4. Restore power by switching the breaker back on. Leave the wall switch in the off position until you are ready to test.
  5. Run cold water into the sink and turn the disposal on. A healthy unit should spin freely without a hum, repeated clicking, shaking, or unusual sound.
  6. If the disposal starts but the sink still does not drain, move to Step 6. If it hums without spinning, stop and follow Step 3.

How to tell it worked: The disposal runs normally, and water and light food waste move into the drain instead of remaining in the sink.

Some units also have a small electrical cord plug with a reset or overload feature. Follow that plug’s instructions. Never cut, splice, or bypass an electrical plug.

Step 3 Free a disposal that hums but does not spin

A humming disposal usually means the motor has power but the impeller cannot turn. Food, a bottle cap, a utensil, or a damaged key may be holding the blades against the housing. The motor can heat quickly in this condition, so turn it off if it continues to hum.

  1. Switch off the breaker and wall switch. Never use the reset button as the only power control while your hands are near the blades.
  2. Use a flashlight to look into the disposal. If a hex key is visibly stuck in the impeller, do not pull on it while the power is on.
  3. If the disposal normally uses a hex key or special wrench, insert it into the socket at the bottom of the disposal while the power is off.
  4. Turn the tool in the direction that frees a stuck object. Apply steady force without twisting the motor housing or bending the tool. If the key will not move, stop rather than using excessive force.
  5. If the obstruction is visible near the opening, remove it with tongs or the disposal tool. Keep fingers and loose metal objects away from the blades.
  6. Remove the tool, restore the breaker, run cold water, and briefly test the disposal. If it spins freely, let water run while you dispose of small scraps.

How to tell it worked: The humming stops during the test, the impeller turns without shaking, and water drains normally.

If the hum continues, the key turns but the blades do not move, or the motor smells hot, switch off the breaker and call a qualified appliance repair professional. Do not keep restarting it.

Step 4 Clear a jammed key or stuck impeller

If the disposal spins unevenly, stops when a spoon or similar object touches the blades, or makes a scraping sound, the flywheel may be stuck in one position. This can happen when a jam shifts the blades, a key loosens, or debris packs tightly around the impeller.

  1. Turn off the breaker and the disposal’s wall switch. Place a flashlight and the correct tool within reach before starting.
  2. Remove the sink’s drain guard or strainer if you need a clearer view. Keep all screws and parts in the bucket.
  3. Try the manufacturer’s approved hex key or wrench in the impeller socket. Turn it slowly in both directions only as far as the instructions allow.
  4. If the blades remain stuck, check for a visible obstruction from above. Use tongs or a disposal tool to remove reachable debris without putting your hand inside.
  5. Rock the tool gently while maintaining steady pressure. Do not strike the disposal, insert a pry bar into the motor housing, or force the blades sideways.
  6. Once the blades move, remove the tool and any debris. Restore power, run cold water, and test the disposal briefly.

How to tell it worked: The blades rotate smoothly in both directions when you turn them with the tool, and the disposal no longer hums or catches on utensils.

Step 5 Check for a disposal that will not start at all

If the disposal is completely silent, the problem may be a tripped reset, a wall-switch or plug issue, a blown breaker, or a failed motor. You can check the accessible parts, but do not open the motor housing or repair internal wiring.

  1. Confirm that the wall switch is off, then check the labeled breaker. If the breaker has tripped, switch it fully off before resetting it once.
  2. If the disposal is plugged into an outlet under the sink, check the plug only after the breaker is off. Unplug it and look for obvious damage, heat marks, or a loose plug.
  3. Do not remove the receptacle cover or examine exposed wiring. If the outlet looks damaged, call a qualified electrician.
  4. Restore the plug and breaker, then use the reset button according to the manufacturer’s instructions.
  5. Run cold water and test the disposal for a short time. If it stays silent, has a burning smell, or trips the breaker again, switch it off at the breaker.

How to tell it worked: The disposal starts from the wall switch and runs without repeated breaker trips, unusual noise, or a burning smell.

A repeatedly tripped breaker, a warm plug, a scorched outlet, or a disposal that smells burned needs professional service. Do not bypass the breaker or reset it repeatedly.

Step 6 Clear the sink drain below the disposal

A disposal can run normally while the sink still will not empty. If cold water in the sink does not move, the blockage is likely in the sink tailpiece, the trap, the branch drain, or a connected dishwasher line. Start with the simplest accessible check.

  1. Switch off the disposal’s breaker. If you will disconnect a dishwasher hose or sink fitting, close the sink’s water shutoff valve before opening any connection.
  2. Place a bucket under the disposal and the P-trap. A sink drain connection may drip when loosened.
  3. Check the sink strainer and the opening above the disposal for debris. Remove only parts that are designed to come out without disturbing the plumbing.
  4. If your installation allows access without removing the disposal, disconnect the hose leading to the dishwasher. Open the dishwasher filter basket or accessible debris cap if the manufacturer’s instructions call for it, and clear food residue.
  5. Run cold water into the sink while watching the drain and dishwasher connection. If either line does not flow, reconnect everything before continuing.
  6. If the blockage appears to be in the sink tailpiece or trap and you are comfortable with basic plumbing, remove the P-trap according to local instructions. Empty the contents into the bucket and look for the obstruction.
  7. Use a drain snake through the sink opening only if the tool will not damage the pipe or disposal. Do not force it past a sharp obstruction.
  8. Reconnect the trap with the fittings in the same orientation and snug but not overtightened. Restore the breaker, if applicable, and run water to check for leaks.

How to tell it worked: Water drains from the sink and dishwasher connection flows freely, with no backup, leaking trap, or remaining disposal jam.

If a sink has a separate dishwasher connection, a backed-up dishwasher drain can also affect the sink. Use only the dishwasher’s accessible filter or debris cap; do not open concealed dishwasher plumbing.

Step 7 Remove a lodged object or clear an internal obstruction

If a spoon, bottle cap, packaging, or another hard object falls into a running disposal, it can lodge between the blades and the housing. Removing it from above may restore drainage without taking the unit apart.

  1. Switch off the breaker and wall switch. Do not reach into the disposal while it is energized.
  2. Shine a flashlight into the drain and locate the object. If you can see and reach it, use tongs or a disposal tool to pull it out.
  3. If the object is wrapped around the blades, use the approved hex key or wrench to turn the impeller in the freeing direction while you apply light tension with the tool.
  4. If the object is deeply lodged or the blades will not turn, stop. Trying to reach farther can damage your hand or the disposal.
  5. Once the object is removed, turn the blades by hand with the tool and check that they move freely. Restore power, run cold water, and test the unit.

How to tell it worked: The disposal spins without obstruction, and the sink drains normally when you run it with cold water.

Step 8 Use a sink plunger on a remaining drain blockage

If the disposal spins normally but the sink drain still backs up, the remaining problem may be a blockage in the drain pipe. A sink plunger can create enough pressure to dislodge a soft obstruction without using harsh chemical cleaner.

  1. Make sure the disposal is off. Fill the sink with enough water to cover the plunger cup.
  2. Place the plunger over the drain opening and make a tight seal.
  3. Pump slowly at first, then increase the speed while keeping the cup sealed. Add more water if it starts draining too quickly.
  4. Repeat several times, then remove the plunger and let the sink drain.
  5. If water does not move, remove the plunger and check for a visible obstruction at the strainer. Do not use the plunger if the sink cannot hold enough water to cover the cup.
  6. Run the disposal only after confirming that the impeller spins freely and the sink drain is open.

How to tell it worked: The sink empties after plunging, and running cold water no longer causes it to back up.

Do not use a plunger if you removed the sink’s drain opening and cannot restore it securely. Do not pour boiling water, caustic cleaner, or an improvised chemical mixture into the drain.

Step 9 Test the repair and monitor the drain

A short test after each repair can prevent you from repeating the problem or leaving the disposal running against another obstruction. Listen as well as watch, because a change in sound often appears before a full backup.

  1. Turn on cold water and run the disposal for a brief test. Feed in only a small amount of soft food waste, if needed.
  2. Listen for smooth motor noise, repeated clicking, humming, rattling, or vibration. Stop the disposal if you hear any of the abnormal sounds.
  3. Check that water leaves the sink promptly and that the dishwasher, if connected, still drains.
  4. Look under the sink for drips around the disposal, dishwasher hose, tailpiece, and trap. If you disturbed a fitting, tighten it only by hand or with the correct tool.
  5. Restore the sink strainer, drain cover, or disposal guard so nothing can fall into the opening.
  6. If the disposal starts normally but the sink drains slowly, clean the sink strainer and repeat the drain check before assuming the disposal motor has failed.

How to tell it worked: The disposal starts and stops normally, water drains without backing up, and the drain connections remain dry.

Symptom checker

What you notice Likely cause Fix (step number)
The sink fills with water and will not empty Debris at the sink opening or a blocked drain below the disposal Steps 1 and 6
The disposal hums but the blades do not turn Jammed food, a lodged object, or a stuck impeller Steps 3 and 7
The disposal starts, stops, and starts again Tripped overload or reset control Step 2
The disposal is completely silent Switch, plug, breaker, reset, or motor failure Steps 2 and 5
The disposal runs but the sink will not drain Sink trap, branch drain, or dishwasher connection blockage Steps 6 and 8
A utensil stops the blades when the disposal is running Stuck flywheel, jam, or displaced key Step 4
The disposal makes a rattling sound Loose or damaged key, debris around the impeller, or loose mounting parts Steps 3, 4, and 7
Water drains slowly but does not back up Partially blocked strainer, trap, or branch drain Steps 1, 6, and 8
The breaker trips when the disposal starts Electrical fault, motor problem, or water inside the unit Step 5

Mistakes that make it worse

  • Putting your hand into the disposal. Use tongs or a disposal tool, and make sure the power is off first.
  • Continuing to run a humming motor. Repeated starts can overheat the motor and turn a simple jam into a burned unit.
  • Ignoring a burning smell, smoke, or a tripped breaker. Turn off the breaker and arrange qualified service.
  • Pouring chemical drain cleaner into the disposal. It can damage seals, pipes, and connected appliances, and may create dangerous fumes.
  • Using a pry bar or pliers on the motor housing. These tools can crush the housing, damage the key, or harm the motor.
  • Leaving the dishwasher hose disconnected. Reconnect and test every line you loosen before running the disposal again.
  • Using boiling water on a seized disposal. Heat can crack plastic or distort metal parts.

When to call a professional

  • Call a plumber if the sink, dishwasher connection, trap, or branch drain remains blocked after the accessible clearing steps, or if you see a leak after reconnecting plumbing.
  • Call a qualified appliance repair professional if the disposal hums without turning, the impeller stays seized, the reset does not restore power, or the unit will not start after the electrical checks.
  • Call a qualified electrician if the breaker trips again, the wall switch or outlet is hot or damaged, or the disposal smells burned. Do not open the receptacle or repair internal wiring.
  • Stop and call for help if you find a damaged electrical cord, moisture inside the motor housing, a scorched outlet, or a humming unit that continues after power is restored.
  • If the blockage is deep in the main sewer line or repeats in several drains, call a plumber. Do not try to clear a main line yourself.

How to keep it from happening again

  • Run cold water before and after using the disposal so waste stays wet and moves toward the drain.
  • Feed food in small batches rather than dropping a large amount into the opening.
  • Keep hard and fibrous items out of the disposal, including utensils, packaging, bones, fruit pits, and stringy foods.
  • Clean the sink strainer and removable disposal guard regularly.
  • Check the dishwasher connection and sink trap for drips or slow drainage before a backup becomes severe.
  • Never use the disposal to break up a sink backup. Clear the drain first.
  • Keep the reset button accessible and leave enough room under the sink to service the unit safely.

Frequently asked questions

Why is my garbage disposal humming but not spinning?

A hum usually means the motor has power but the impeller is stuck against food, an object, or a damaged key. Turn off the breaker, remove the obstruction with a tool, and free the impeller with the approved key. Stop if it remains seized or smells hot.

Why won’t my garbage disposal drain even though it runs?

The disposal may be clear while the sink drain is blocked. Check the strainer, dishwasher connection, sink trap, and branch drain. Run cold water before testing so you do not mistake a drain blockage for a disposal failure.

How do I reset a garbage disposal?

Turn off the disposal’s breaker, find the reset button on the motor housing, and press it as directed in the unit’s instructions. Restore power and test with cold water. Resetting does not remove a jam, so stop if the disposal hums without spinning.

Can I use a garbage disposal after it hums?

No. A humming unit is trying to move against an obstruction. Switch off its breaker, unplug it if that controls the outlet, and clear the jam before testing it again. Repeated running can overheat the motor.

What should I not put in a garbage disposal?

Keep utensils, glass, metal, plastic caps, bones, fruit pits, and fibrous foods out of the unit. These items can jam the impeller or damage the blades and pipes.

When should I call a plumber instead of clearing the disposal myself?

Call a plumber if the sink remains blocked after you clear the strainer and accessible drain connections, or if water leaks from a loosened fitting. A blockage that affects several drains may be deeper in the main line and should not be treated with chemical cleaner.

What this guide is based on

Revision history

  1. Updated and re-checked against sources.
  2. First published.

Did this fix it?

Mixtvnowcom.org editors Editorial team

The Mixtvnowcom.org editors write and check every guide on the site against the manufacturer instructions and official sources it lists, and keep each guide's revision history up to date.

More guides from the editors