On this page

Quick answer

Most often, a dirty filter, trapped food, a kinked drain hose, a clogged disposal, or a blocked air gap slows drainage. Unplug the dishwasher or switch off its breaker, remove standing water, clean the filter, check the hose, and test a short cycle before arranging repair.

At a glance

Time
15–60 min
Difficulty
Easy
You'll need
Towels, bowl, cup, flashlight, warm water, soft brush, and basic tools
Cost
Free for most fixes; a part if one is worn
Works on
Most household dishwashers with a user-accessible filter
Not covered
Internal wiring, sealed pump parts or hidden plumbing repairs

Why does a dishwasher stop draining?

A dishwasher moves dirty water from the bottom of the tub through a filter and sump. The drain pump then sends that water through a hose connected to a sink drain, an air gap, or a garbage disposal. Some models leave a small amount of water in the pump housing, but water covering the tub floor, returning after drainage, or increasing during the next fill is not normal.

Food particles, grease, and small pieces of glass commonly collect in the filter or sump. A disposal can jam, an air gap can trap debris, and a drain hose can kink when the dishwasher, sink, or cabinet contents are moved. Less often, the drain pump, drain valve, control, or float system fails and the appliance cannot move or contain water correctly.

Need to know how to unclog a dishwasher drain? Start with the accessible parts because a clogged filter is easier to correct than a failed pump. Cleaning the filter, checking the hose, and testing the disposal resolve many cases without opening the appliance. If those checks do not work, the symptom points more strongly to the pump, valve, control, or a hidden connection.

Before you start

Switch off the dishwasher’s breaker or unplug it before touching the filter, standing water, drain hose, disposal connection, pump area, or nearby electrical parts. Turn off the disposal’s power switch before working at the sink drain, and unplug it if it has a plug. If you disconnect a water line under the sink, close the under-sink valve first.

Keep the floor dry and spread towels beneath the connections you will inspect. If the standing water is hot, let it cool before handling it. Wear gloves if the water contains food, grease, or possible broken glass, and use tongs rather than bare fingers to remove sharp fragments.

Have a bowl or bucket, a cup or ladle, dry towels, a flashlight, warm water, mild dish soap, a soft brush or bottle brush, and basic hand tools ready. Keep the appliance manual nearby because filter locations, hose fittings, air gaps, and accessible pump screens differ among dishwashers.

Step 1 Reset the dishwasher and clear a stalled cycle

Why this helps: A dishwasher can remain paused, waiting for the door to latch, or holding a cycle that never reached its drain phase. Canceling that cycle and resetting the power can clear some control conditions without requiring a repair.

  1. Use the cancel or stop control described in the appliance manual. Do not pull the door open while water is moving through the drain pump.
  2. Switch off the dishwasher’s breaker. If the dishwasher has a plug, unplug it instead.
  3. Check that the plug and outlet are dry, then reconnect the plug or restore the breaker.
  4. Make sure the door closes and latches. Move dishes, utensils, or a rack that may be keeping the door from seating correctly.
  5. Confirm that the filter and lower rack are seated properly. An item caught under the filter can interfere with drainage.
  6. Start the shortest rinse or wash cycle available on your model with the dishwasher empty.
  7. Watch the visible water level. Note whether it drops during the drain phase, stays still, or returns after the cycle ends.

If the dishwasher has a display or error message

Record the message before resetting the appliance. A message about a drain, pump, or water-level fault may narrow the diagnosis, but the same visible checks remain safe. If the controls stay inactive after the power reset, do not remove the control panel or touch internal wiring.

How to tell it worked: A successful reset lets the dishwasher enter the drain phase and removes visible water from the tub. If the water remains at the same level or the cycle stalls again, the problem is likely mechanical or in the drain route.

Step 2 Clean the dishwasher filter and sump

Why this helps: The filter catches food and debris before they reach the drain pump. When that material builds up, water can remain above the filter, and the pump may not pull enough water through the sump to empty the tub.

If the filter is beneath the lower rack

  1. Switch off the dishwasher’s breaker or unplug it before reaching into the tub.
  2. Slide out the lower rack and remove dishes and silverware so nothing can fall into the filter recess.
  3. Locate the round filter, flat mesh screen, or combined filter assembly at the lowest point of the tub.
  4. Release the filter according to its shape and the appliance manual. A twist-lock filter turns, while some lift-out filters come straight up.
  5. Do not force a component that does not move as expected. Check the manual if you cannot identify the release.
  6. Rinse the filter under warm running water and rotate it so debris leaves the center, edges, mesh, and tabs.
  7. Add a small amount of mild dish soap if grease remains, then rinse the filter thoroughly.
  8. Use a soft brush, ladle, or damp towel to clean the filter recess and the area around the sump opening.
  9. Use tongs to remove loose fragments if you suspect broken glass. Keep your fingers clear of the filter opening.
  10. Replace the filter so it sits flat and locks in place. Make sure the rack cannot press against it.

If the manual identifies another filter location

Some models place a removable filter in the door or use a separate screen in another location. Clean only a part the manual identifies as user-accessible. Do not remove a sealed pump cover to reach a filter you are not sure about.

Do not poke into the pump opening, remove the pump impeller, or use a sharp tool to pull debris from the sump. Those actions can damage the pump or expose electrical parts.

How to tell it worked: After the filter is clean, water should recede more quickly during the drain phase and should not remain above the filter opening. If the tub still holds water, inspect the hose, air gap, and disposal before moving to the pump.

Step 3 Remove standing water safely

Why this helps: Removing standing water prevents overflow and spills while you inspect the filter and drain connections. It also makes it easier to judge whether water leaves the basin during the next test cycle.

  1. Turn off the dishwasher’s breaker or unplug it before reaching into the basin.
  2. Spread towels across the floor and place a bowl or bucket where you can empty it safely.
  3. Use a cup, ladle, or measuring scoop to remove water from the lowest visible part of the tub.
  4. Keep the tool from jamming into the filter or pump opening.
  5. Pour the collected water into the bowl rather than letting it run across the floor.
  6. Remove visible food pieces with tongs. If broken glass may be present, do not use bare hands.
  7. Repeat until the water is below the filter rim. Do not tilt the dishwasher forward or sideways.
  8. Wipe the filter recess and lower tub with a damp towel, then dry water that could reach the door seal or cabinet base.
  9. Check beneath the dishwasher for another leak or puddle before restarting it.

Do not pour water containing glass, food, or heavy grease into the sink drain. It can create another blockage or carry sharp fragments into the disposal.

How to tell it worked: Standing water should no longer be visible above the filter area. During the next cycle, the level should drop rather than remain or rise. A small amount below the filter opening may be normal on some models.

Step 4 Inspect the dishwasher drain hose

Why this helps: Food and grease can collect at the hose opening, and a hose can become flattened or kinked when the appliance is moved. Either problem can stop water even when the filter and pump are working.

  1. Switch off the dishwasher’s breaker or unplug it before handling the hose.
  2. Place a bowl and towels under the sink connection because trapped water may come out.
  3. Follow the visible hose from the dishwasher outlet toward the sink drain, air gap, or garbage disposal.
  4. Look for food at the opening, a tight bend, a crushed section, a loose connection, or pressure from a shelf or cabinet edge.
  5. Disconnect the hose only if the fitting is accessible. Support it so it does not pull on the dishwasher.
  6. Loosen a hand-removable clamp or simple fitting according to its design. Do not twist a connection that is not meant to turn.
  7. If the opening is accessible, clear loose debris with a soft bottle brush. Do not force a wire, screwdriver, or coat hanger deep into the hose.
  8. Check that the hose is not cracked, punctured, badly flattened, or crushed behind the dishwasher.
  9. Reconnect the hose fully to the proper outlet and secure the clamp or fitting without crushing the hose.
  10. If you replaced a damaged hose, follow the installation instructions for its shape and connection.

If the hose is hidden behind the dishwasher

Do not pull the appliance forward unless the installation guide directs you to do so. The guide should explain how to shut off the water, support the appliance, and restore its position. If moving it risks pulling on the water line or an unknown connection, call a professional.

How to tell it worked: Water should pass through the hose without backing up, and the dishwasher basin should empty during the drain phase. A hose that remains visibly kinked or does not reconnect securely still needs correction.

Step 5 Clear the disposal or sink drain connection

Why this helps: A dishwasher that drains through a garbage disposal depends on both the disposal and the dishwasher inlet being open. A jammed disposal can make sink water and dishwasher water back up in the same drain route.

If the dishwasher connects to a disposal

  1. Turn off the disposal’s wall switch. Unplug the disposal if it has a plug, and keep the dishwasher’s breaker off while its hose is disconnected.
  2. Run cold water into the sink and briefly restore power to the disposal if it is safe to do so.
  3. Listen for spinning and check whether the sink drains normally.
  4. If the disposal hums, buzzes, or does not spin, switch it off again. Do not put your hand into the disposal chamber.
  5. Follow the disposal instructions to release a reset or clear an accessible obstruction. Stop if the obstruction remains lodged or the disposal continues to hum.
  6. Disconnect the dishwasher hose from the disposal inlet if the connection is accessible and the instructions allow it.
  7. Keep a bowl and towels under the connection because water may spill out.
  8. Inspect the inlet for food, grease, or glass. Remove only debris that the instructions say you can access safely.
  9. Check both appliance manuals before removing a dishwasher knockout plug. If the dishwasher already drains through the disposal, an inlet plug may already have been removed.
  10. Reconnect the hose so it seats fully in the inlet. Secure the clamp without crushing the hose.
  11. Restore the disposal power and run it briefly with cold water. Confirm that the sink drains freely.
  12. Start a short dishwasher cycle and confirm that the tub empties.

If the dishwasher drains directly into the sink drain

  1. Keep the dishwasher’s power off while you inspect the visible connection.
  2. Run the sink faucet and check whether the sink drains normally.
  3. With the power off, look for debris at the visible dishwasher hose opening.
  4. Remove only loose debris with a soft brush. Do not insert metal tools into the sink drain.
  5. If the sink drains slowly or backs up while the dishwasher is off, the sink drain needs separate attention.

Never operate the dishwasher while its drain hose is disconnected. If the disposal leaks, hums, vibrates badly, or will not spin after the approved clearing method, stop using it and arrange service.

How to tell it worked: The disposal should spin and drain freely, and the dishwasher hose should remain seated without leaking. The dishwasher should then empty normally. If the disposal still fails, the fault may be inside the disposal rather than the dishwasher.

Step 6 Clean the air gap or direct drain opening

Why this helps: An air gap is a small fitting between the dishwasher hose and the sink drain. It can collect food, grease, and glass even when the dishwasher filter and garbage disposal are clean.

<3>If your installation has an air gap

  1. Switch off the dishwasher’s breaker or unplug it before handling the fitting.
  2. Find the small air-gap fitting beside the faucet or above the sink drain.
  3. Place a towel beneath it and remove the cap or insert by hand if it is designed to come apart.
  4. Do not pry or twist a fixed fitting, and do not remove parts that are not meant to separate.
  5. Use a soft brush or bottle brush to remove debris from the opening and visible hose section.
  6. Check that the hose enters the fitting fully and that no glass or food is trapped against the opening.
  7. Reinstall the insert and cap according to their design.
  8. Keep the air gap installed if the installation instructions require it.
  9. Run the sink drain or disposal briefly, then start a dishwasher cycle.

If there is no air gap

Inspect the direct sink-drain opening only if it is accessible. With the disposal switched off, remove loose debris with a soft brush and keep metal tools and your hands out of the opening. If the connection is hidden behind the sink or cabinet, do not dismantle it.

How to tell it worked: Water from the sink or disposal should flow away without backing up, and debris should no longer appear at the dishwasher hose opening. The dishwasher basin should empty during the next drain phase.

Step 7 Correct the drain-hose route

Why this helps: The hose must allow water to move toward the sink without forming a trapped pocket or being pressed against a sharp edge. A new bend can make an otherwise clear hose stop draining.

  1. Keep the dishwasher’s breaker switched off or the dishwasher unplugged while you move or secure the hose.
  2. Trace the hose from the dishwasher outlet to the sink connection.
  3. Follow the installation guide for the required high loop, downward slope, and connection method.
  4. Keep the section after the high loop directed downward toward the sink. Avoid a new upward bend that could trap water.
  5. Check that the hose is not compressed behind the dishwasher, trapped under a leveling foot, or pinched by a pipe or cabinet brace.
  6. Secure the hose where it can rub against metal, a pipe, or a moving shelf.
  7. Use the attachment method shown in the installation instructions rather than improvising a support.
  8. Leave enough slack that closing the sink cabinet does not pull, stretch, or crease the hose.
  9. Confirm that the outlet is fully open and the hose is secure in the sink drain, air gap, or disposal inlet.

Do not create a new routing shape simply to make the hose fit. Follow the appliance and sink installation instructions because the correct arrangement depends on how the two are connected.

How to tell it worked: The hose should retain its shape after the cabinet closes, and sink water should not flow back into the dishwasher. During the test cycle, the dishwasher’s water level should fall during the drain phase.

Step 8 Check the drain pump and accessible pump screen

Why this helps: If the filter and drain route are clear but the basin does not empty, the pump may be obstructed or may not be moving water. Some models include a user-accessible screen or debris trap that can be checked without dismantling the appliance.

  1. Complete Steps 1 through 7, reinstall the filter and racks, and confirm that every hose connection is secure.
  2. Run the dishwasher empty on a short cycle and watch the visible water level from outside the appliance.
  3. If the water recedes, let the cycle finish so you can confirm that the water does not return.
  4. If the water remains or rises, cancel the cycle and switch off the breaker before reaching into the tub.
  5. Consult the appliance manual for a user-accessible pump cover, screen, or debris trap.
  6. Remove only the part the manual identifies for user access.
  7. Clear loose, visible debris with the tool or method specified in the manual.
  8. Do not remove the pump impeller, reach past an electrical component, or open a sealed housing.
  9. Replace the accessible cover exactly as intended, reinstall the racks, and restore the breaker.
  10. Run another short cycle and observe whether the water drops and stays down.

If the pump runs but does not move water

A hum without visible water movement can indicate debris around the pump or another blockage. Another common sign is a cycle that stops repeatedly at the same point. Do not keep restarting the dishwasher in that condition. A drain valve, pump motor, control, float, or internal electrical fault requires professional diagnosis.

How to tell it worked: The basin should empty during the drain phase, and no new water should collect after the cycle ends. If the pump remains silent, hums continuously, or runs without reducing the water level, the accessible checks have ruled out the common external causes.

Symptom checker

What you notice Likely cause Fix (step number)
Standing water remains after the cycle Dirty filter, trapped debris, or a blocked drain route 2, 4
Water rises during the next fill Drain pump, drain valve, or float-system fault 1, 8
Water returns after the disposal runs Blocked air gap, disposal inlet, or incorrect hose route 5, 6, 7
The disposal hums but does not turn Disposal jam or failed disposal motor 5
The hose is bent or pinched near the cabinet Kinked or compressed drain hose 4, 7
Draining is slow and produces an odor Food, grease, or debris in the filter, hose, or disposal 2, 4, 5
Water appears under the dishwasher but the tub is empty Drain-hose or connection leak 4
Only a small amount remains below the filter opening Normal residual water if the level stays stable 2
The cycle will not start or cancel Door latch, control, or power condition 1
Water drains but remains around the sink Blocked sink drain or air gap 5, 6
The cycle stops repeatedly at the drain phase Pump obstruction, valve fault, or control problem 8
The hose connection leaks during draining Loose, damaged, or incorrectly seated hose 4, 7

Mistakes that make it worse

  • Running repeated full cycles while standing water remains, which can increase spills and hide the original blockage.
  • Pouring chemical drain cleaner into the dishwasher, which can damage seals, the pump, or the hose and create a hazardous splash.
  • Using a wire, screwdriver, coat hanger, or bare hand inside the pump or garbage disposal.
  • Reconnecting the drain hose with a sharp bend, loose clamp, or new kink inside the cabinet.
  • Skipping the filter, air gap, or disposal because the hose looks clear from above.
  • Removing sealed panels, pump parts, terminals, or internal wiring without the correct instructions and tools.

When to call a professional

  • Water remains in the tub after the filter, hose, air gap, and disposal have been checked.
  • The drain pump hums, buzzes, stalls, runs without moving water, or repeatedly stops the cycle.
  • The drain hose is crushed, disconnected, or trapped inside the cabinet or wall.
  • Water leaks from the hose, sink connection, or disposal connection, or the leak source is hidden.
  • The repair requires replacing a sealed pump, drain valve, control, float, electrical terminal, or internal wiring.
  • The disposal leaks, hums, vibrates badly, or remains jammed after you follow its approved clearing steps.
  • The dishwasher must be moved but its water line, leveling feet, or under-sink connections are uncertain.

How to keep it from happening again

  • Clean the filter on the schedule listed in the appliance manual.
  • Scrape food from plates and rinse off heavy grease before loading the dishwasher.
  • Keep large scraps, bones, and glassy food debris out of the drain area.
  • Check the air gap or sink-drain connection whenever food collects near the faucet.
  • Inspect the drain hose after moving the dishwasher, sink, or cabinet contents.
  • Watch for standing water or leaks beneath the appliance so you can act before the problem spreads.

Frequently asked questions

Is a little water left in the bottom of my dishwasher normal?

Some designs leave a small amount of water in the pump housing below the filter. If the level stays below the filter opening, does not grow, and has no odor, it may be normal. Standing water above the filter or water that returns after draining is not normal.

What is the safest first fix for a dishwasher not draining?

Start by switching off the breaker or unplugging the dishwasher. Remove standing water, clean the filter, and inspect the accessible drain hose. If those steps do not correct it, check the disposal or air gap before testing another cycle.

Why is water still in my dishwasher after I cleaned the filter?

The filter may be clean while the hose, air gap, or disposal inlet is still blocked. It is also possible that the drain pump or drain valve is not moving water. Complete the external checks before assuming the pump needs replacement.

My garbage disposal works; does that prove the dishwasher drain is clear?

No. The disposal can run normally while the dishwasher hose is kinked, the air gap is blocked, or the dishwasher pump is not moving water. Check those parts separately and then run a dishwasher test cycle.

Can baking soda or vinegar clear a dishwasher drain?

Baking soda and vinegar are not reliable ways to remove food, grease, glass, or a pump obstruction. They can leave residue in the sump that makes later cleaning harder. Clear the filter, hose, disposal, or air gap instead.

Should I repair or replace a dishwasher that will not drain?

First complete the accessible cleaning and hose checks. If the pump, valve, control, wiring, or a sealed connection needs service, a qualified technician can diagnose whether repair is practical. Do not open sealed electrical parts to judge the repair yourself.

What this guide is based on

Revision history

  1. Updated and re-checked against sources.
  2. First published.

Did this fix it?

Mixtvnowcom.org editors Editorial team

The Mixtvnowcom.org editors write and check every guide on the site against the manufacturer instructions and official sources it lists, and keep each guide's revision history up to date.

More guides from the editors