On this page

Quick answer

Check the breaker and any nearby ground-fault circuit interrupter, then look for a door that is not latching, an engaged control lock, delayed start, or an incomplete cycle selection. If lights are on, close the door fully and start a normal cycle. If there are no lights, restore power and check the outlet before inspecting the appliance.

At a glance

Time
15–45 min
Difficulty
Easy
You'll need
Flashlight, outlet tester, and model manual
Cost
Free for most checks; service or a part may cost extra
Works on
Electric household dishwashers, built-in or portable
Not covered
Gas appliances, fixed wiring, and sealed control-board repairs

Why is a dishwasher not turning on?

An electric dishwasher needs power at its outlet or branch circuit, a closed and latched door, and an active wash-cycle command. The control panel uses those inputs to decide whether to begin filling and run the wash pump. If a required signal is missing, the dishwasher may remain idle even when the display and buttons appear active.

If the dishwasher won’t start, no lights usually point to the household power path first: a tripped breaker, a reset ground-fault circuit interrupter, a loose plug, or a damaged cord. If the dishwasher lights on but won’t start, the usual causes are a door latch, an engaged control lock, a delayed or paused cycle, or a start-control or latch-switch fault. Separating these symptom groups helps you avoid replacing parts that are not the problem.

Work from the simplest checks toward the most involved.

Before you start

Power: Before checking a plug or outlet, switch off the dishwasher’s breaker or unplug the dishwasher. Do not remove an outlet cover or touch fixed wiring. Have a licensed electrician handle wiring repairs.

Water: Before checking the supply valve, disconnecting a hose, or moving the dishwasher, switch off its breaker or unplug it and close the water supply valve. Let any standing water cool before reaching near it.

Gas: This guide covers electric dishwashers. If you smell gas, leave the area, avoid flames and electrical switches, and call the gas utility or emergency services from outside. Never work on gas lines, gas valves, or burners; call a licensed professional.

Have your model manual, a flashlight, a dry cloth, and a plug-in outlet tester ready. Keep towels nearby, but do not wedge the door open with them. If the dishwasher is hardwired, use the breaker instead of trying to unplug it. Record any message on the display exactly as it appears because fault information differs among models.

Step 1 Check the breaker and restore power

A tripped breaker or ground-fault circuit interrupter can leave the dishwasher completely unresponsive. A loose plug or an outlet without power can create the same symptom. Check this path before opening the appliance or changing any settings.

Switch off the breaker before touching the dishwasher plug or outlet. Do not remove an outlet cover.

  1. Find the outlet that powers the dishwasher. It may be under the sink or in a nearby cabinet, but the location varies. If you cannot identify it, do not disconnect several plugs or guess at the circuit.
  2. Switch off the breaker that serves the dishwasher. Unplug the appliance if it has a plug, then check that the plug is fully seated and that the visible cord has no obvious damage.
  3. Turn the breaker back on. If it trips again, switch it off, leave the dishwasher unplugged, and arrange service rather than repeatedly resetting it.
  4. If the outlet has ground-fault protection, press its TEST button and then RESET once while the dishwasher is unplugged. If it will not stay reset, stop troubleshooting and call a qualified electrician.
  5. After restoring power, use a plug-in outlet tester to check a standard receptacle if needed. A fault indication means you should stop and call a qualified electrician. A plug-in tester cannot check a hardwired dishwasher connection.

How to tell it worked: The display lights, the controls respond, or the dishwasher begins its startup sequence. If the outlet has power but the dishwasher remains dark, continue with the door and control checks before arranging service.

Step 2 Make sure the door is fully latched

Most dishwashers will not begin a wash cycle while the door is open or only partly secured. A dish, utensil, rack, or package can hold the door away from the latch. A misaligned door or a dirty latch opening can also prevent the control panel from detecting that the door is closed.

  1. Push the racks fully into position so they do not hold the door open. Move any tall item that may interfere with the door’s closing path.
  2. Close the door firmly. Feel or hear for the latch to engage, but use your model manual if you are unsure what a normal latch feels like.
  3. Look along the door edge, gasket, and latch opening for food, labels, or packaging. Remove the obstruction and wipe the area with a dry cloth.
  4. Check whether the door sits evenly in the cabinet opening. If it slants, catches, or remains slightly open, stop forcing it and follow the manual’s hinge-adjustment instructions.
  5. Close the door normally and try the cycle-selection and start sequence in Step 4.

How to tell it worked: The door stays closed without being held, and the control panel accepts the start command. If the door closes but the controls still show that it is open, the latch or its switch may need professional service.

If the latch is hidden

Some built-in models place the latch behind a trim panel. Use the model manual to locate it, shine a flashlight into the opening, and remove only loose debris that you can see. Do not pry the trim, bend the latch, or reach into the mechanism. If the door has visible hinge screws, make only the adjustments described in the installation manual.

Step 3 Release the control lock and reset the controls

An engaged control lock can leave the panel illuminated while ignoring buttons. The controls may also remain unresponsive after a power interruption. Releasing the lock or performing a permitted power reset often restores normal button response.

  1. Look for a lock indicator on the display or panel. Some models show a padlock symbol, while others provide no indicator, so check the model manual.
  2. Find the lock-release control and follow its exact press-and-hold instructions. Do not substitute a random combination of buttons or keep pressing after the panel confirms the change.
  3. If the lock is already released, perform a power reset: switch off the breaker, unplug the dishwasher with dry hands, wait a few minutes, reconnect it, and turn the breaker back on.
  4. After the panel initializes, press a control that only opens the door or changes a display setting. This confirms that the panel is responding without starting an unwanted cycle.
  5. If the buttons respond but the wash still will not start, return to Steps 2 and 4. If the panel stays unresponsive, continue to Step 8.

How to tell it worked: The lock indicator disappears, the display responds, and buttons accept commands. Repeatedly holding buttons is not a substitute for identifying the correct control.

If liquid reached the controls

Disconnect the power before touching the panel. If liquid is on the exterior, let it dry fully and reconnect only when everything is dry. If liquid entered the control housing, do not open the cover; arrange service.

Step 4 Select a wash cycle and press Start

A dishwasher can display the correct time and still wait because it is paused, set to delay start, or waiting for a valid cycle. A drying-only or rinse-only selection does not perform the full wash sequence you are trying to test. Control layouts vary, so follow the labels and sequence in your manual.

  1. Read the panel and identify the selected cycle, delay setting, and pause indicator. Cancel any delay using the manual’s control.
  2. Select a normal or heavy wash cycle. Choose the shortest available wash cycle if you want a brief test, but do not select a drying-only option.
  3. Press the main Start or Resume control once. Do not hold it unless the manual specifically instructs you to hold that button.
  4. Follow the model’s door sequence. Some models require the door closed before Start is pressed; others expect Start to be pressed and then the door closed.
  5. Watch the display and listen briefly. A running indication, filling, or motor sound confirms that the command was accepted.

How to tell it worked: The display shows an active cycle and the dishwasher begins moving water or running the motor. If it starts and then stops before washing, continue with the water and drain checks. If Start flashes or nothing changes, revisit the control lock and door latch.

If the display shows a delayed start

Cancel the delayed timer before choosing a new cycle. Confirm that the display no longer shows a delay, then press Start again. If the delay returns by itself, note that behavior and check the manual’s settings instructions.

If the display appears blank but the panel works

Some models use a sleep display that dims after a period of inactivity. Press a display or control button and watch for the display to brighten. If no response appears, check the breaker and control lock again.

Step 5 Check the water supply and inlet

If the controls accept Start but no water enters the dishwasher, check the supply valve and inlet hose. A closed valve, kinked hose, clogged inlet screen, or damaged connection can stop the wash before it begins.

Before checking the supply valve or hose, switch off the dishwasher’s breaker or unplug it and close the water supply valve. Stop if you cannot identify the water valve; do not guess.

  1. Locate the household water shutoff valve that serves the dishwasher. It is commonly under the sink, but your installation may differ. If the pipework or valve is not clearly labeled, ask a plumber to identify it.
  2. With the power off and the water valve closed, inspect the hose between the valve and the dishwasher for kinks, pinches, cracks, bulges, or wet spots.
  3. If your model allows access to an inlet screen, remove the screen according to the manual. Rinse a removable screen gently if instructed; do not enlarge the opening or push debris farther inside.
  4. If the hose must be disconnected to inspect it, keep the power off and water closed. Do not force a stuck fitting. If the hose is cracked, leaking, or cannot be reseated, have it replaced by a qualified technician or plumber.
  5. Reconnect the hose, open the water valve slowly, wipe the connections dry, and restore the dishwasher’s power.
  6. Start a wash cycle and confirm that water enters the tub. If the valve and hose look normal but the tub remains dry, stop cycling and arrange service.

How to tell it worked: Water enters the dishwasher and the cycle continues toward the wash stage. A fixed supply problem will not usually explain a completely blank panel, so also confirm power if the display remains dark.

Step 6 Clear the drain path and filter

A clogged filter or blocked drain can stop a cycle after it starts, rather than prevent the panel from lighting. Food debris, a bent drain hose, and debris around the sink air gap are common places to look. Do not assume a drain problem explains a dishwasher that never receives power.

Switch off the breaker or unplug the dishwasher before reaching near standing water or touching the filter area. Let the water cool, and do not put your hand into a disposal.

  1. Let the dishwasher stop, then switch off its power before opening the door and reaching into the tub.
  2. Remove the lower rack and locate the filter as shown in the model manual. Some models have a removable filter; others have a nonremovable screen.
  3. Remove visible food debris carefully and rinse the filter only as the manual permits. Do not dismantle the pump housing or reach near exposed blades.
  4. Inspect the sink air gap beside the disposal, if present. Turn off the disposal’s power, remove the grate only if permitted, and clear visible debris with a suitable tool. Never run the disposal while clearing it.
  5. Check the drain hose beneath the sink for kinks or crushing. Follow the manual if the hose connects to a disposal; do not pull it out or push it farther into the disposal by guesswork.
  6. Restore power, start a wash cycle, and watch whether the drain pump runs and the tub empties.

How to tell it worked: Water drains away, no standing water remains, and the cycle continues without stopping at the same point. If the filter cannot be removed or the drain remains blocked, call a technician.

If there is no removable filter

Follow the manual’s instructions for cleaning the filter screen. Do not drill an access hole, remove the pump cover, or pour a cleaner into the drain as a substitute for clearing a blockage.

Step 7 Inspect the plug, cord, and cabinet opening

A loose plug, pinched cord, or damaged connection can interrupt power just as effectively as a tripped breaker. Check these visible problems before assuming the control system has failed.

Unplug the dishwasher or switch off its breaker before inspecting the cord or plug. If you must move the appliance, close the water supply valve first.

  1. Inspect the full visible length of the cord. Look for cracks, crushed sections, discoloration, a loose plug, or exposed metal. Do not touch bare conductors.
  2. Check that the plug is fully seated and that the receptacle does not move when you hold the plug body. Do not pull on the cord.
  3. If the plug or receptacle is loose, hot, discolored, or shows a burning odor, stop using the outlet. Have a qualified electrician or appliance technician inspect it.
  4. Look for the cord being pinched between the cabinet, a shelf, or a hose. Reroute it only if you can do so without moving the appliance. If movement is necessary, close the water valve and follow the installation manual.
  5. Do not tape a damaged cord, splice wires, or change the plug yourself. Have the cord or connection replaced by a qualified technician.

How to tell it worked: The panel stays responsive and a normal cycle begins after the connection is corrected. Visible cord or plug damage should be repaired rather than left in place for later.

If the dishwasher is hardwired

Do not try to disconnect it. Switch off the breaker before inspecting the cabinet area. A missing receptacle, loose connection, or wiring damage requires a licensed electrician; do not remove a junction-box cover.

Step 8 Use the diagnostic procedure or arrange service

If power is confirmed, the door latches, and the controls respond but the dishwasher still will not start, the start button, door switch, control module, or related wiring may be faulty. These faults require diagnosis rather than random button combinations.

  1. Find the model number and locate the correct manual. Write down any displayed fault message exactly as it appears; fault codes are model-specific.
  2. Use a built-in diagnostic only if the manual explains the exact control sequence. Enter and exit it as directed, and do not improvise with several buttons.
  3. Record the symptoms for service: no display, display on with no start, flashing Start control, error message, or a display that reports the door as open.
  4. If the diagnostic identifies the door switch, start control, control module, or another internal fault, arrange repair service. Do not bypass the door latch or alter internal wiring.
  5. Ask the technician to test the start control, door switch, wiring harness, and control module as appropriate. Fixed wiring must be handled by a licensed electrician.

How to tell it worked: The diagnostic procedure identifies the fault and gives you a specific repair path. After the required repair, the door should latch, the Start command should be accepted, and the dishwasher should enter an active wash cycle.

If you cannot find the manual

Locate the model and serial labels on the appliance or installation documents, then use the manufacturer’s official support site. Do not force panels to find a label and do not enter undocumented diagnostic combinations.

Symptom checker

What you notice Likely cause Fix (step number)
No lights or display Tripped breaker, reset ground-fault protector, or outlet without power 1
Display is on, but the dishwasher will not begin Door not fully latched 2
Lock symbol appears or buttons are ignored Control lock engaged 3
Display shows a pause or delayed start Paused cycle or delay setting 4
Cycle starts but stops before water enters Closed supply valve or blocked inlet 5
Water enters but does not drain Clogged filter or blocked drain path 6
Start control flashes without starting Door-switch fault, invalid setting, or control fault 2, 3, then 8
Breaker trips as soon as the dishwasher starts Possible electrical fault 1; stop and call an electrician
Power comes and goes, or the plug feels loose Loose connection or pinched cord 7

Mistakes that make it worse

  • Forcing the door, latch, buttons, or control panel instead of checking for an obstruction or misalignment.
  • Running the dishwasher after a leak or while a plug or outlet is wet.
  • Resetting a breaker repeatedly after it trips again.
  • Holding random button combinations, which can enter a diagnostic mode or change settings.
  • Reaching into a disposal, pump housing, or energized control area with your hands.
  • Ignoring a kinked inlet hose, clogged filter, or blocked drain until the cycle stops midwash.

When to call a professional

  • The breaker trips again, the outlet shows a fault, or you notice heat, discoloration, or a burning smell. Switch off the breaker, leave the dishwasher unplugged, and call a licensed electrician.
  • The cord, plug, receptacle, or fixed wiring is damaged. Do not splice, tape, or rewire it yourself.
  • The panel stays unresponsive after power, latch, and control-lock checks. An appliance technician can test the controls and internal connections.
  • The diagnostic procedure identifies a start-button, door-switch, or control-module fault, or the Start control continues flashing.
  • Water is leaking, the supply fitting will not turn, or a hose is cracked. Close the water supply valve and call a plumber or qualified appliance technician.

How to keep it from happening again

  • Clean the filter on the schedule in your model manual and check the drain path when the filter is due for cleaning.
  • Wipe the door gasket and latch area regularly, and remove dishes or packaging that can obstruct the door.
  • Keep the inlet and drain hoses free of kinks, and replace a damaged hose through a qualified technician or plumber.
  • Keep the plug, receptacle, and surrounding cabinet area dry, and check that the plug remains firmly seated.
  • Use the appliance regularly and follow the manufacturer’s recommended cleaning procedure when prompted.

Frequently asked questions

Why is my dishwasher not turning on?

If there are no lights, check the breaker, ground-fault protector, plug, and outlet first. If the panel lights but the cycle will not begin, check the door latch, control lock, and selected cycle.

Why do the lights come on but the dishwasher will not start?

The door may not be fully latched, the control lock may be engaged, or the dishwasher may be paused or set to delay start. Close the door securely, release the lock, cancel any delay, and select a wash cycle.

How do I reset a dishwasher that will not start?

Switch off the breaker, unplug the dishwasher, wait a few minutes, and reconnect it. After the panel initializes, confirm the controls respond, then choose a wash cycle and press Start once.

Is it safe to use the dishwasher if the breaker keeps tripping?

No. Turn off the breaker, unplug the dishwasher, and stop using that circuit until a qualified electrician checks it. Repeatedly resetting the breaker can hide an electrical fault.

Do I need a technician if there are no lights?

First confirm that the outlet and breaker supply power. If the outlet is working but the dishwasher remains completely unresponsive, arrange appliance service or have a qualified electrician check the connection.

What should I do if the Start button flashes?

Check that the door is latched, the control lock is off, and a wash cycle is selected. If it continues flashing, record the model number and exact message, then use the model’s diagnostic instructions or arrange service.

What this guide is based on

Revision history

  1. Updated and re-checked against sources.
  2. First published.

Did this fix it?

Mixtvnowcom.org editors Editorial team

The Mixtvnowcom.org editors write and check every guide on the site against the manufacturer instructions and official sources it lists, and keep each guide's revision history up to date.

More guides from the editors