On this page
Quick answer
Bluetooth usually fails because the device is out of range, not powered on, already paired to another device, or blocked by a stale pairing record. Start by checking power and battery, moving closer, toggling Bluetooth off and on, removing the device from saved devices, and pairing again. Restart the phone or computer if those settings changes will not take effect.
At a glance
- Time
- 15–45 min
- Difficulty
- Easy
- You'll need
- Charged devices, a charger, and access to Bluetooth settings
- Cost
- Free for most fixes; service or a replacement part if hardware fails
- Works on
- Phones, computers, TVs, speakers, headphones, controllers, and similar setups
- Not covered
- Internal wiring, gas appliances, or component-level hardware repair
Why is my Bluetooth device not connecting?
Bluetooth has two separate stages: pairing and connecting. During pairing, the accessory and the phone, computer, TV, or speaker exchange information and save a trusted link. On later uses, the host looks for that saved link and asks the accessory to reconnect. A connection can fail even when the accessory is nearby if the radio is off, the accessory is still linked to another host, or one side has a stale pairing record.
The radio link also depends on power, distance, obstacles, wireless congestion, compatible Bluetooth profiles, and working software. A headset may pair for calls but lack a profile needed for music, while a game controller may work through its own receiver instead of direct Bluetooth. Low battery, a disabled adapter, an operating-system update, or a firmware setting can interrupt a link without indicating a broken accessory.
If you see “bluetooth won’t pair,” most problems fall into a few groups: the accessory is not in pairing mode; it is connected elsewhere; the host has Bluetooth or its pairing list in a bad state; the devices are too far apart or surrounded by interference; software or drivers need attention; or the radio hardware has failed. Testing the accessory with a second compatible host separates a host problem from an accessory problem before you replace or reset anything.
Before you start
Bluetooth troubleshooting usually changes settings rather than opening equipment, so you can begin without taking anything apart. If a step involves a mains-powered appliance, unplug it or switch off its breaker first. Keep liquids away from the device, and do not charge a battery that is swollen, hot, leaking, or damaged. If a Bluetooth module is built into a fixed appliance, do not remove its covers.
Do not remove a valve, alter a supply line, open a burner housing, or touch internal electrical wiring. Those jobs require a licensed professional.
Before trying each fix, charge both devices and keep their instructions nearby. You will also need a working charger and, if possible, another compatible phone or computer for isolation testing.
- Charge the accessory and the phone, computer, TV, or speaker that will host it.
- Note which devices the accessory has connected to before.
- Keep any device passcodes, Wi-Fi passwords, and sign-in details available.
- Use a second compatible Bluetooth device for testing, if one is available.
Step 1 Check both devices and reduce the distance
Why this helps: Bluetooth accessories need power, an active radio, and a workable distance. A device may also remain connected to another phone or computer, preventing the new host from taking control of it.
- Charge the accessory and its host until each shows a normal power or battery state.
- Turn on the accessory and confirm that its status light or on-screen indicator is active.
- If another device is connected, open that device’s Bluetooth list and choose Disconnect or Forget.
- Move the accessory much closer to the host and keep a clear path between them.
- If the accessory does not respond, turn it off, confirm its power source, and turn it back on.
For earbuds and other wearables
Place both earbuds or the wearable in its charging case, close the case, and reopen it. If the manufacturer’s instructions show a pairing button or button sequence, follow that sequence exactly rather than holding every control you can find.
How to tell it worked: The accessory appears in the host’s Bluetooth list and connects without repeated drops. Confirm the actual function afterward, such as sound, calls, controls, or data transfer.
Step 2 Reset the Bluetooth radio and restart the host
Why this helps: A Bluetooth radio can become stuck even when it appears enabled in the settings. Toggling it clears some temporary states, while restarting closes background apps and reloads the operating system’s connection services.
- Open the host’s Bluetooth settings.
- Turn Bluetooth off and wait for the on-screen status to change.
- Turn Bluetooth back on and check whether the accessory appears.
- If airplane mode is active, turn it off or use its Bluetooth control, depending on the device.
- Close apps that may be using Bluetooth audio, calls, keyboards, mice, or nearby-device scanning.
- Restart the host with its normal Restart command, then power-cycle the accessory.
If the host is a computer
Open the operating system’s Bluetooth and device settings and turn the adapter off and on. If the computer uses a USB Bluetooth adapter, unplug it, reconnect it, and try another port. Avoid uninstalling the driver until you have checked the simpler settings and software updates.
How to tell it worked: The host can discover or reconnect to the accessory after the restart. If the adapter no longer appears in the computer’s device list, continue with the driver and isolation checks.
Step 3 Remove the old pairing and pair again
Why this helps: A saved pairing can become corrupted or remain associated with another host. Clearing both sides forces the accessory and host to negotiate a fresh connection instead of reusing bad information.
- On the host, open the Bluetooth or connected-device list and find the accessory.
- Choose Remove, Forget, Unpair, or the equivalent option.
- On the accessory, clear its saved host list using the documented pairing control or reset button.
- Put the accessory into pairing mode and make it discoverable.
- On the host, select the accessory’s exact name, confirm any pairing prompt, and wait for Connected.
If the host displays a passkey or confirmation code that you did not initiate, cancel the prompt and begin the pairing process again. Never approve an unexpected request.
For audio accessories
After connecting headphones or a speaker, select it as the output device. If calls are part of the problem, also check whether the accessory is selected as the microphone and whether the host has separate Bluetooth audio settings for calls and media.
For controllers and keyboards
If the accessory uses a dedicated wireless receiver, reconnect the receiver to the computer and press the controller’s documented connect control. A receiver and the accessory itself do not normally need to be paired to the computer at the same time.
How to tell it worked: The device reconnects automatically after one manual pairing, and its intended function works normally. If pairing succeeds but sound or controls do not work, continue checking profiles and output selection.
Step 4 Reduce interference and test a clear location
Why this helps: Bluetooth uses a limited wireless range. Walls, furniture, people, crowded wireless equipment, and active household electronics can weaken the signal or make an established connection unstable.
- Move the host and accessory close together, with no wall or large object between them.
- Move away from active wireless equipment, cordless phones, and other Bluetooth devices that are not needed.
- Pause nearby Bluetooth audio temporarily to determine whether another device is holding the connection.
- Test the pair in another room or another clear part of the same room.
- If the host uses a USB adapter, try a different port and place the adapter away from crowded cables.
If it fails in only one location
A problem that follows the same location usually indicates range, obstruction, or interference rather than a damaged radio. Keep the devices closer, change the placement of the host or adapter, and remove nearby wireless equipment one at a time to identify the source.
How to tell it worked: The connection stays active in the previously troublesome location, or you identify an object or device that consistently causes the failure. A stable connection should also remain active while you move the accessory normally.
Step 5 Update software, firmware, and drivers
Why this helps: Software updates can correct Bluetooth discovery, pairing, audio-profile, and driver problems. Firmware changes can do the same for an accessory, especially after it has been paired with many hosts.
- Install pending operating-system updates through the device’s built-in update tool.
- Check the accessory manufacturer’s official app for a firmware update.
- Restart both devices after installing updates.
- On a computer, check the Bluetooth driver through the operating system and the adapter maker’s official support page.
- On a phone, review nearby-device, Bluetooth-scanning, and app permissions that the official app requires.
- Reopen the Bluetooth list and attempt the connection again.
For a computer driver
If the adapter shows an error marker, first disable and enable it, then restart the computer. Update or reinstall the driver only when the operating system or adapter maker provides an appropriate package. Avoid driver files from unknown download sites.
For phone permissions
Some phones require permission to scan for nearby devices. If the official app or system settings explain that requirement, enable the needed permission. If a location permission is requested for scanning, review the request and allow only what you are comfortable permitting.
How to tell it worked: The accessory is discovered or reconnects after the update. If the same problem continues on every compatible host, the issue is more likely in the accessory or its radio hardware.
Step 6 Reset saved Bluetooth and network settings
Why this helps: Resetting the host’s Bluetooth and network state can clear damaged pairing records, an unresponsive service, or corrupted settings. This is more disruptive than toggling Bluetooth and should come after the simpler checks.
A network or Bluetooth reset can remove saved networks and paired accessories. Record your Wi-Fi passwords and other information you will need before continuing.
- Back up important data and note the accessories and networks you use.
- On a phone, open the system reset options and choose the specific Bluetooth or network reset available.
- On a computer, remove forgotten Bluetooth devices, restart the computer, and use a Bluetooth-specific reset if one is clearly labeled.
- On the accessory, use only its documented full reset control if a pairing-only reset did not help.
- Turn Bluetooth on and pair the accessory again as if it were new.
- Reconnect any other Bluetooth accessories or services you use.
If the reset affects Wi-Fi or mobile service
Some devices combine Bluetooth, Wi-Fi, and mobile-network options in one reset. Reconnect to the required networks, confirm airplane mode is off, and verify that the Bluetooth option is enabled before testing again.
How to tell it worked: The host can add and use the accessory after the reset. If the device still does not appear, avoid repeating resets and continue with isolation testing and service.
Step 7 Test another host to isolate the fault
Why this helps: Testing separates a problem in the original host from a problem in the accessory. It also shows whether the failure follows the device or follows the location.
- Record which hosts fail and which ones you can test without disrupting another setup.
- Pair the accessory with a second compatible phone, tablet, or computer.
- On the original host, test a different Bluetooth accessory that you know works.
- Compare the results: an accessory that fails everywhere points toward the accessory, while a host that rejects every accessory points toward its settings, software, or adapter.
- If the computer uses a USB adapter, try another port and confirm that the adapter appears in the operating system’s device list.
Do not open the computer to inspect a built-in adapter. A missing adapter, repeated connection drops on every host, or a loose internal connector requires service.
How to tell it worked: The test identifies which side is failing. If the accessory works on the second host, repair or reset the original host; if it fails on the second host as well, move to accessory recovery or service.
Step 8 Restore the device and arrange service if needed
Why this helps: A built-in factory reset can repair corrupted system state, but it removes the user’s data and settings. Use it only after the simpler resets have failed, because it cannot repair damaged radio hardware.
Back up the device before a factory reset. Do not use undocumented button combinations, and do not open the housing to reach the Bluetooth module.
- Back up or sync important data and confirm that you can restore your accounts and settings.
- Use the manufacturer’s built-in factory-reset option and follow each prompt.
- For an accessory, use its documented full reset only; do not open it or combine unrelated button holds.
- After setup, enable Bluetooth and pair the accessory again.
- If it still fails on multiple hosts, stop resetting and contact the manufacturer or an authorized repair provider.
- Arrange service immediately if the device is hot, swollen, smoking, sparking, or physically damaged.
For a computer
Use the operating system’s built-in recovery or repair option before a full reinstallation. Back up first and obtain any installation files from the operating-system maker. If the Bluetooth adapter is missing from the hardware list after recovery, the computer needs hardware service.
How to tell it worked: The restored device discovers, pairs, and maintains the intended Bluetooth function. If it does not, the remaining fault is likely hardware-related and should be evaluated by a qualified repair provider.
Symptom checker
| What you notice | Likely cause | Fix (step number) |
|---|---|---|
| The accessory never appears in the Bluetooth list. | It is off, not in pairing mode, too far away, or its host radio is disabled. | Steps 1, 2, and 3 |
| A previously paired accessory will not reconnect. | A stale pairing record or an active connection to another host. | Steps 1 and 3 |
| The connection drops after a short time. | Weak signal, interference, low power, or another nearby device taking the connection. | Steps 1 and 4 |
| The device pairs but produces no sound. | The wrong output or input is selected, or an audio profile is unavailable. | Steps 3 and 5 |
| It works on one phone but not on a computer. | The computer’s adapter, driver, or audio settings are blocking the connection. | Steps 2, 5, and 7 |
| The computer cannot find any Bluetooth adapter. | The adapter is disabled, disconnected, missing a driver, or failing. | Steps 2, 5, and 7 |
| It works near the host but fails across the room. | Range, obstruction, or wireless congestion is likely. | Step 4 |
| Every nearby device fails to pair with it. | The accessory may have a dead battery, corrupted settings, or failed radio hardware. | Steps 1, 7, and 8 |
Mistakes that make it worse
- Pairing repeatedly without first removing the old saved connection.
- Leaving the accessory connected to another phone or computer during testing.
- Holding undocumented buttons or combining button holds that trigger unwanted resets.
- Erasing a device before backing up accounts, files, and network information.
- Installing Bluetooth drivers or accessory software from unknown download sites.
When to call a professional
- The device is hot, swollen, leaking, smoking, sparking, or giving off a burning odor. Unplug it or switch off its breaker if you can do so safely, then arrange service.
- The Bluetooth adapter is absent from the operating system, remains disconnected, or fails on every compatible host.
- A built-in module, internal antenna, connector, or circuit board needs inspection or replacement.
- The Bluetooth equipment is part of a fixed appliance, vehicle installation, or electrical system. Do not open it or work on hidden wiring.
- Call a licensed professional and do not attempt those jobs yourself.
- A critical medical, hearing, or safety device remains unreliable after software, pairing, and factory resets.
How to keep it from happening again
- Keep host software, accessory firmware, and computer drivers current.
- Charge the accessory regularly and replace a damaged battery only through an authorized provider.
- Remove old host entries when selling, giving away, or retiring a phone or computer.
- Turn accessories off when they are not in use so they do not remain available for unwanted connections.
- Keep paired devices within a clear path and avoid crowded areas when the connection is unstable.
- Clean dusty charging and pairing areas with a dry, soft method approved by the manufacturer; do not use metal tools or moisture.
Frequently asked questions
Do I need to reset my entire phone or computer?
A full factory reset is usually the last step because it removes your data and settings. Try restarting, removing the saved pairing, and resetting Bluetooth or network options first. Back up the device before using factory reset.
Why does my Bluetooth device show as connected but have no sound?
The connection may be active while the host is sending audio to another output. Select the Bluetooth device as the output and check separate call and media settings. The devices may also lack a compatible audio profile.
Why is my Bluetooth device not showing up when I scan?
The accessory may be off, already connected elsewhere, or outside pairing mode. Move it close to the host, disconnect it from other devices, and clear the old pairing before trying again.
Can another phone or computer help me find the problem?
Yes. If the accessory works on a second host, the original host is the likely problem. If it fails on every compatible host, the accessory, its power source, or its radio hardware is more likely at fault.
Should I remove the Bluetooth driver and reinstall it?
Not until you have tried toggling the adapter, restarting the computer, and checking for official updates. If the adapter is missing or fails on other accessories, reinstall the correct driver or arrange hardware service.
Is it safe to press the small reset button on my accessory?
It is safe only when the manufacturer identifies the control as a reset or pairing button. Follow the documented procedure and avoid holding unrelated buttons together. Resetting may remove saved hosts but should not affect other devices.
What this guide is based on
- Apple Support support.apple.com
- Google Support support.google.com
- Microsoft Support support.microsoft.com
Revision history
- Updated and re-checked against sources.
- First published.
Did this fix it?
Thanks. Glad it's sorted.
Sorry it's still not right. Recheck the symptom checker above, or tell us what you're seeing.